Jump to content
SAU Community

Recommended Posts

Cusco/Saftey 21 6-Point bolt in full cage

For R34 2-Door, bought to track the 34 but I'm getting a 180 as a track car instead, so need to sell it. The R33 ones of these on Nengun are $1000+. It comes with all of the mounting plates, bolts, cusco foam to cover the whole thing.

Located in Perth, Western Australia. Postage to Melbourne is $200ish so yeah will post at buyers expense.

Price; $800 ONO

0420 307 580

[email protected]

safety21-cage.jpg

Link to comment
https://www.sau.com.au/forums/topic/315185-r34-saftey-21-roll-cage/
Share on other sites

hay mate

yeah u should still be able to have rear seats in but u have to cut a small hole for them to fit as all r34 cages mount to the same place which is the wheel arches. ill put some pic up tonight of how they mount my cage however doesnt allow for back seat passengers so mine are removed.

my friend has one of these in his silvia and has kept back seats with a small trim and u can still sit in there.

8110 - the middle hoop is connected to the front and rear section of the cage by bolts so it is all removable. i already have a half cage (rear section) so i just want the front yeah.

op - i need some photos of how the front connect to the roll over hoop and they need to be high res and of both side just so i can estimate where they will bolt on to mine as i have an interesting cage set up

Sure guys, I'll smash some photos up in a bit from my DSLR, I havn't put it together so they'll just be of the pieces.

If you're both keen, cause you're both in Melbourne would be cheaper to post, either work out between yourselves how you want to divide the cost or I'll do it for you, up to you.

I got it from Japan, via Melbourne, and the leg between Melbourne to Perth was $200. I'm keen to get it out of here to buy new turbo and such, so if you're over east then I'll do it for $700 plus postage, to make the postage cost a little lower.

And Geraus, I'm not sure if it would or not, I'm sure with enough cutting of thigns you could get it to fit but yeah. Worst things worst you'd have the cage there in Melbourne, and there's a lot more people who track R34's over there =p

I got it through Import Monster, found it online and got them to bring it it, it's not something they stock. I'm losing a heap of money on it, paid more to buy it in Japan than I'm selling it for, not including the shipping.

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...