Jump to content
SAU Community

Recommended Posts

gota clean out the shed, Lots of parts,

all cheap

---------

R32 parts

---------

complete right door with trim, $70

complete left door with trim, $70

gtst bonnet $100 type-m blue

gtst bonnet $100 primer

gtst bonnet, cut lip, needs patchin $50

right guard, $70

left guard $70

boot lid with spoiler, type-m $70

boot lid with spoiler holes, $50

rear bar $50

rb20det Block, has all parts, pistons, crand, rods ectt, just head removed, $100

front and rear suspension and brake setup 5stud

-discs

-calipers

-hubs

-caster arms

-upper arm stuff

- $500 for full kit

Full car wiring loom with all moduels and fuse boxez ect, $100

manual tailshaft $60

sway bar $30

gtst diff $100

interior parts, ask got lots,

gtst seats, front and rear $150

gtr rear seats, $200

---------

R33 parts

---------

complete right door with trim $70

s2 dash with airbag, mint condition $150

s2 front seats $150

R33 gtst front and rear, Discs, Calipers, Hubs, Caster arms, upper arms, complete setup $700

gtst s2 diff, $100

manual tailshaft $100

lots of interior parts, ask me

Need everything gone, got other parts i didnt mention

western suburbs, melbourne

i will only post small stuff, if you can organise postage for larger items i will send

0411980023

Edited by boz_soljah
Link to comment
https://www.sau.com.au/forums/topic/315717-cheap-r32-r33-parts-garage-cleanout/
Share on other sites

hey man just wondering do you still have the

"front and rear suspension and brake setup 5stud

-discs

-calipers

-hubs

-caster arms

-upper arm stuff

- $500 for full kit" ?? and i was wondering how much do you think it would cost to send it to Adelaide ??

hey man just wondering do you still have the

"front and rear suspension and brake setup 5stud

-discs

-calipers

-hubs

-caster arms

-upper arm stuff

- $500 for full kit" ?? and i was wondering how much do you think it would cost to send it to Adelaide ??

still got it, pm sent

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...