Jump to content
SAU Community

Recommended Posts

1997 R33 Series 2 125,000kms

Serviced Every 5000km or less with Motul turbo light 10w 40w

Motul Diff Oil

Redline Gearbox Oil

Modifications,

Apexi Power FC Tuned at 12psi (made 201kw)

Blitz Dual SBC boost controller

Split Fire Coil Packs

Walboro Fuel pump

Blitz turbo timer

R34 Turbo (OP6)

RB20 Wastegate Actuator (10 psi)

Split Dump/front Pipe

3in Hi Flow cat (inside not bashed out)

3.5 inch HKS Hi Power Exhaust From CAT back

Apexi Power intake filter on custom made Metal intake pipe onto the turbo

(Pod not totally boxed in but covered over see photos below)

Standard RB20 Blow off valve

Greddy Front Mount Inter cooler and piping

Alloy Radiator

Heavy Duty Excedy Clutch

Braided Clutch Line

Braided Brake Lines (ADR approved)

Master cylinder stopper

Front and Rear Strut Braces

Bilstein Shocks and King Springs

Front Whiteline adjustable Castor Bushes (adjustable on car)

Rear Whiteline Camber Bushes

Work Emotions CR KAI 18 x 8.5 in all round

235/35/18 federal 595 SS on the front (50%)

235/35/18 Sumitomo HTR Z 3 on the rear (50%)

Work blue Wheel Nuts

M Spec side skirts and rear pods

33 GTR rear seat

Have had the Roof lining, A-Pillar and B/C Pillar trims redone in Black Suede (haven't done the sun visors yet)

White LEDs' in the cluster

Have Changed the AC Panel, cigarette lighter surround and ignition barrel surround lights all to blue LEDs'

Pioneer Head Deck (DEH-P6850MP)

Pioneer Front Speakers and tweeters

Pioneer Rear 6in Speakers

And finally the rear "Skyline" Boot garnish lights up red with taillights

There is probably more little bits and pieces i have forgotten, Basically the car has never missed a beat in the last 2 years runs great, drives beautifully and handles well. Has been my pride and joy for a little over a year but its time for me to move on, Pictures Below feel free to ask any questions.

Price - $14,900 Will get RWC upon Sale

I am willing to remove some parts to bring the price down.

Plates Not Included

Brisbane QLD

PM for my contact details if you are interested

and i also have a few more photos too.

Cheers Scott

post-29410-1270853707_thumb.jpg

post-29410-1270853726_thumb.jpg

post-29410-1270853737_thumb.jpg

post-29410-1270853748_thumb.jpg

post-29410-1270853762_thumb.jpg

post-29410-1270853801_thumb.jpg

post-29410-1270853816_thumb.jpg

post-29410-1270853838_thumb.jpg

Unable to pm you as i don't have 10 posts.

Would you be able to send me more images of the interior.

For $10,500 does it come with EVERYTHING ELSE other then WORK WHEELS, POWER FC AND BOOST CONTROLLER

What condition are the stock wheels at?

Cheers

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...