Jump to content
SAU Community

Recommended Posts

Hmm well it looks like my last post from yesterday got deleted, I was about to update my location etc

well I'll re-post properly. It's a 1990 r32 gtr, has not been complied yet but still can be at top secret imports.

It was privately imported by someone else(guy I purchased from). It needs paint on doors and rear quater pannel,

it has late model doors with side intrusion fitted factory. Had really minor dents on rear quater, but have been

repaired. It is gun metal grey, has after market dash so it has 36000km on it, I'm suspecting it has more like 70000km

on it. Has original interior, which is in great condition. Has gtrs twin turbo upgrade, electronic boost controler with low

boost settings(9psi low, 14high). Has barely been driven at all in aust. It has only been garaged and started monthly.

Has got 3in 5zeigen exhaust full system. Has ac installed in glove box and 5 vital gauges fitted in center conspl cluster, gauges are

exhaust temp, fuel pressure, boost, water temp, oil pressure I am selling due to financial problems, also, I never got it complied because

I wanted to fix it right up and make sure it was awsome before I did it. Pics should be posted this arvo

I'm asking $8500 Ono for it

I'm located in maitland nsw 2320. Which is about 1.45 north of sydney

my e-mail is [email protected]

phone- 0434633055. I am happy to call you

if you wish, just send me a text,

Cheers, Jordan

Link to comment
https://www.sau.com.au/forums/topic/316478-r32-gtr/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
×
×
  • Create New...