Jump to content
SAU Community

Recommended Posts

hey guys,

ive got a few parts left over from my other parts sale... so while im at my current work, there is free freight on everything.. delivered to your home or workplace via courier.

stock RB20 turbo... run standard boost only, excellent condition - $150.00

RB20 clutch hub and fan - unmolested, excellent condition - $50.00

RB20 j-pipe to throttle body - comes with bov, - $20.00

RB20 alternator - good nick, has been pulled down and inspected, bearings good, brushes good, contacts cleaned - $40.00

RB20 coilpacks - good condition, $40.00

R32 gtst bonnet - gunmetal grey, excellent condition - $100.00

r32 gtst bootlid - gunmetal grey, with or without spoiler - $100.00

stock RB20 clutch - reasonably worn but good for reco or to throw in to get you out of trouble - $30.00

R32 gtst/S13 silvia RHF lower control arm - good cond, happy ball joint - $30.00

R32 gtst/S13 silvia RHF castor rod - good condition - $20.00

GTR/GTS4 alloy engine mounts - $30.00

R32 gtst stock shocks and springs, good condition, no leaks, no sponge, no noise - $150.00

what ive listed is what im selling, if i havent listed it, im not selling it, so please dont ask.

pics on request.

located in east maitland/thornton/newcastle.

cheers

Linton

Hey are engine mounts fit rb20 to???

they arent the rubber mount... they are the alloy supports/brackets/etc that bolt in between the engine and the mount

only if the rb20 is in the gts4.. i was hoping to modify them to fit my gtst, one side comes close.. the other side is completly different.

hey mate,

am interested in the turbo. Just after a bit of info,

-are the rb20 turbos similar in size as those on rb25? if not, can u tell me the diffs?

-also is the rb20 turbo T3 flanged?

and hows the shaft play etc?

Cheers

Carl

Hey Champ, interested in the R32 GTST shocks and springs. Are they complete strut units? Have been told by one person that there are 2 different types and i am a little concerned about purchasing the wrong ones. Any info would be appreciated and also a contact phone No. Cant send PM's as i have only just registered.

Thanks

Hey Champ, interested in the R32 GTST shocks and springs. Are they complete strut units? Have been told by one person that there are 2 different types and i am a little concerned about purchasing the wrong ones. Any info would be appreciated and also a contact phone No. Cant send PM's as i have only just registered.

Thanks

i think the 2 different types your hearing about is r32 gtst and gtr are different in the rears.

they are the complete get up, springs and shocks, all together, unbolt and bolt in, no mucking around. my number is 0431646160, just text me as i generally dont answer and ill reply with my account details.. whats your address and ill get them ready.. cheers

Is the RB20 Altenator the same as a RB25 Altenator? I need one for my RB25 powered 240Z

i assume so.. cant see why they would be any different. cheers. if you want it, text me on 0431646160

bonnet sold to me pm already sent

sent pm and text msg... cheers mate.

cheers

Linton

coilpacks sold

shocks and springs pending payment

bonnet pending payment

everything else still up for grabs... will take offers on anything..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...