Jump to content
SAU Community

Recommended Posts

I have for sale a set of R32 GTR calipers with 60% pads included and a set of standard (Cross drilled) R32 GTR Rotors (Discs)

The calipers are made by Sumitomo and are alloy, not cast iron so they are lighter.

One of the rear rotors has 2 cracks from two of the outer holes to the edge only on the outside face.

Diameter and Thicknesses for Rotors:

Fronts : 296mm x 31mm & 30.7mm

Rears : 297mm x 17mm & 17mm

New they are:

Fronts: 32mm thick

Rears: 18mm

Wear Limit (from gtr manual)

Fronts: 30mm

Rears 16mm

Rotors have done 104000 kms. Still a fair bit left on em.

For those who dont know, front calipers are 4 pot, rears are 2 pot.

Apparently they are good upgrades for an S13 or S14.

Not sure what else they will fit on so have an ask around.

They are in good nic and i'm after $700 (price changed 20/1) for the lot. Not much price diff without the discs, so you can have them or not.

I am in Bunbury, which is about 2 hours south of Perth. So WA buyers preferable but willing to come to freighting arrangements if neccessary.

Cheers

RichyR32GTR

[email protected]

Link to comment
https://www.sau.com.au/forums/topic/31700-r32-gtr-calipers/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
×
×
  • Create New...