Jump to content
SAU Community

Recommended Posts

Hi all, need a bit of guidance. Had my newly acquired r34 gtt auto dyno'd and made 145kw at the wheels - is this a bit low for a NEO engine?

Health check revealed nothing bad accept for the fuel mixture was rich, the dyno mechanic explained that the mixture should be around 10 to 11 throughout the run but by car pretty much shot to 14 as soon as boos came on not sure what this means apart from that its thirsty. Also psi peaked early at 9psi but dropped off to 7 for atleast 1/2 the curve due to rich mixture. Not as smooth a power curve as I hoped for form a stock setup.

He then suggested to get an apexi afc.. I think its now called a superafc.

Question is what is the best product out there as far as tuning air/fuel maps for a skyline r34.. and if I do decide to get serious would I be better of getting an entire engine management unit such as power FC.

I have a fair idea of the concepts and theories behind afc & tuning but not familiar with what products are best matched for skylines & in particular the neo rb25

I'm serious about a full ecu, price is not really an issue but I've heard bad stories about lack of experience out there to tune neo's and high knock counts as a result of going custom.

Plus I've seen youtube videos of a 10,000 rpm skyline is this really possible - I would like to one day pursue an engine build that has ability to hit 8 to 9 k rpm, for simplicities sake what would it take to make a rock solid 8000 rpm rb25, is this foolish? .. would it be better to go high torque low rpm

What thoughts are there around having a large high lag turbo plus a supercharger to make up for the lag down low , has anyone tried this?

Link to comment
https://www.sau.com.au/forums/topic/317297-r34-rich-fuel-mixture-apexi-afc/
Share on other sites

the air fuel ratio should be about 10 to 11 for a stock car, and if it has been tuned it should be about 12. 14 isn't richer than 10 or 11, it is leaner. the lower the number the more fuel there is as it is the AIR/FUEL ratio, so when saying 10 or 11 or 14 that is 10 parts air to 1 part fuel. that is unless he is somehow reading the AFRs differently.

for the AFR to be going so lean when boost comes on then you may have a fuel pump issue or a fuel pressure regulator issue. my suggestion would be to forget the SAFC and get yourself a nistune (pretty sure they do them for the r34) and get that tuned. that will cost you less than a PFC, give you the same results and be much better than the SAFC. should cost you under $1000 for the nistune and to get it tuned (similar cost to a SAFC but will give much better gains than a SAFC).

as for the power you made and the behaviour of the boost, that really comes down to what mods you have. if you are still running stock exhaust, or only have a cat back exhaust and still have the stock cat and turbo to cat section of the exhaust then i would say that the power you made is about right, all things considered.

the air fuel ratio should be about 10 to 11 for a stock car, and if it has been tuned it should be about 12. 14 isn't richer than 10 or 11, it is leaner. the lower the number the more fuel there is as it is the AIR/FUEL ratio, so when saying 10 or 11 or 14 that is 10 parts air to 1 part fuel. that is unless he is somehow reading the AFRs differently.

for the AFR to be going so lean when boost comes on then you may have a fuel pump issue or a fuel pressure regulator issue. my suggestion would be to forget the SAFC and get yourself a nistune (pretty sure they do them for the r34) and get that tuned. that will cost you less than a PFC, give you the same results and be much better than the SAFC. should cost you under $1000 for the nistune and to get it tuned (similar cost to a SAFC but will give much better gains than a SAFC).

as for the power you made and the behaviour of the boost, that really comes down to what mods you have. if you are still running stock exhaust, or only have a cat back exhaust and still have the stock cat and turbo to cat section of the exhaust then i would say that the power you made is about right, all things considered.

is 14 too lean in this situation?

the actual data:

psi speed a/f lambda petrol

1.5 70 14.4 .99

1.5 80 14.4 .99

4.3 90 13.6 .93

6.2 100 11.9 .82

8.2 110 11.4 .78

8.3 120 10.9 .75

8.2 130 10.3 .70

8.0 140 10.2 .70

7.8 150 10.0 .69

7.6 160 10.0 .69

no that looks pretty right. the reason being that at light throttle the AFR's will actually be between 14 and 15, controlled by the o2 sensor and the ecu. once you put your foot down the ecu ignores the o2 sensor and reverts to it's mapping and there is where it runs richer.

in the case of your car, it is running rather rich up top and it would greatly benefit from some form of aftermarket ecu, be it a nistune or a SAFC or any other ecu or piggyback. the ideal afr you want is about 12:1 where as you are running as rich as 10:1 (which is common for stock ecu cars).

as for the power it made, what mods do you have? that will be a determining factor as to how good/bad your power is, but considering the boost pressure you were running it doesn't sound too far off what it should be.

no that looks pretty right. the reason being that at light throttle the AFR's will actually be between 14 and 15, controlled by the o2 sensor and the ecu. once you put your foot down the ecu ignores the o2 sensor and reverts to it's mapping and there is where it runs richer.

in the case of your car, it is running rather rich up top and it would greatly benefit from some form of aftermarket ecu, be it a nistune or a SAFC or any other ecu or piggyback. the ideal afr you want is about 12:1 where as you are running as rich as 10:1 (which is common for stock ecu cars).

as for the power it made, what mods do you have? that will be a determining factor as to how good/bad your power is, but considering the boost pressure you were running it doesn't sound too far off what it should be.

No mods at all.

in that case then the power you made is pretty much right. you have to remember that the 206kw they are rated at is at the flywheel and not at the wheels, so the power at the wheels will always be less.

throw on a full exhaust, wind the boost up to about 10psi and you should see that figure rise up to around 170 to 185kw. throw on a frount mount intercooler and raise the boost up to around 12psi and you should see about 190 to 200kw. add a tune on top of that and you should see a bit more again.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...