Jump to content
SAU Community

Recommended Posts

Cleaning my shed out got a few bits to sell. Most of this stuff was taken off a healthy 26 when I did my rebuild. Engine had 145000ks on it and all parts are in good nick with no damage.

TJ Twin Plate clutch with rb26 flywheel, plenty of meat on clutch plates good condition- $150

post-71053-1271834931_thumb.jpg

post-71053-1271835024_thumb.jpg

RB26dett Standard Cam shafts. Good condition - $100

post-71053-1271835149_thumb.jpg

HKS Mushroom Pod Filter. Good condition - $60

post-71053-1271835259_thumb.jpg

post-71053-1271835876_thumb.jpg

Brand new N1 water pump. - $100

post-71053-1271835429_thumb.jpg

6x rb26dett pistons and rods. - $100

post-71053-1271835560_thumb.jpg

RB26dett Standard Oil pickup - $20

post-71053-1271835655_thumb.jpg

RB20DET crossover Pipe - $20

post-71053-1271835752_thumb.jpg

Also have a complete RB20 wiring loom for $80 ono. All prices are ono.

Link to comment
https://www.sau.com.au/forums/topic/317643-shed-clean-out-rb2620-parts/
Share on other sites

Im in Launceston tas.

The clutch was in a standard 32 GTR when I purchased engine. I test drove the car before we pulled the engine out and the clutch seemed strong and had not been abused by the previous owner. I had already purchased a jim Berry clutch so didn't end up using this twin plate.

Was in Launceston the last couple day doing Greg Crick's helicopter. Ownes the Dodge Viper in the Aus GT series. Would have grabbed the N1 water pump off you and the clutch while I was there. Work maintains a few choppers down there so I might hit you up if you have the gear still available soon. Could you pm me your number incase. Cheers

  • 1 month later...
Cleaning my shed out got a few bits to sell. Most of this stuff was taken off a healthy 26 when I did my rebuild. Engine had 145000ks on it and all parts are in good nick with no damage.

TJ Twin Plate clutch with rb26 flywheel, plenty of meat on clutch plates good condition- $150

post-71053-1271834931_thumb.jpg

post-71053-1271835024_thumb.jpg

RB26dett Standard Cam shafts. Good condition - $100

post-71053-1271835149_thumb.jpg

HKS Mushroom Pod Filter. Good condition - $60

post-71053-1271835259_thumb.jpg

post-71053-1271835876_thumb.jpg

Brand new N1 water pump. - $100

post-71053-1271835429_thumb.jpg

6x rb26dett pistons and rods. - $100

post-71053-1271835560_thumb.jpg

RB26dett Standard Oil pickup - $20

post-71053-1271835655_thumb.jpg

RB20DET crossover Pipe - $20

post-71053-1271835752_thumb.jpg

Also have a complete RB20 wiring loom for $80 ono. All prices are ono.

Stuff still for sale no reasonable offer refused

Clutch

HKS Pod filter

Rb 26 Cams

RB26 Pistons and Rods

Rb26 oil pick up

And Complete RB20 wiring loom with all plugs intact

All parts are in good condition

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...