Jump to content
SAU Community

Recommended Posts

Obviously I'm not going to be expecting the reliability of a brand new toyota corolla out of it, so I'm expecting to be spending some dollars in the way of maintenance etc, however I just want to know if they are a generall reliable vehicle, coz hey, being a GTR, you're going to have a little bit of fun with it, right?

  • Replies 148
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Obviously I'm not going to be expecting the reliability of a brand new toyota corolla out of it, so I'm expecting to be spending some dollars in the way of maintenance etc, however I just want to know if they are a generall reliable vehicle, coz hey, being a GTR, you're going to have a little bit of fun with it, right?

I have fun with mine and no problems so far (touch wood). Are you interested in looking over east? Much better selection and you could probably pick up a s3 if that's what you really want. That's what I ended up doing and as they are slightly cheaper over there you still end up with it on the road in perth for a good price.

I have had a look over east and there are some nice S3 GTR's but i really can't be bothered trucking it over (risk of damage to the vehicle even though it is insured), and getting it rego'd. I'd rather look around and buy a nice one over here that's already rego'd and complied.

^^Totally agree. Remember that when things go wrong on a GTR (32,33 or 34) they are go in multiples of $1000. If you have the money to maintain and repair it then go for it. If you need it checked over go to XSpeed as they are the experts with these things. No one else in Perth comes close.

unless they get some apprentice to work on your gtr

i took my car to a toyota specialist of all places to use the correct grade of oil to put in a skyline gearbox

yep they are definitely the experts

Edited by ohno1
Bubba why must you assume that my foot will be welded to the firewall at all times :/

Yeah I know it may not be a cheap exercise, but yes you do have a very valid point.

How reliable are the R33 RB26's? I mean say it has a few resonable mods and is either running stock boost or slightly more than factory? And assuming you give it some curry every now and then....

They have a better oil pump drive compared to early 26's and really, as long as you maintain it well and have a good tune, it should live a reasonably long life.

Yeah, I am aware that the oil pump drive's on the 32 RB26's were weak, so Nissan did strengthen them..

Maybe I'm just being a bir paranoid about buying a GTR, but I just want one that won't give me any trouble or throw a rod lol.

Now, onto the modifications you can do.

Say if you do a turbo-back exhaust (de-cat), pod filters, boost the turbo's a few pounds higher than factory and install a power-fc, how much awhp should if expect within reason on a safe tune?

Its easy to get performance from a GTR with minimal mods, its just a matter of finding a good example, then you can do as you wish. For example, worst case scenario would be buying a GTR that has supporting mods like full exhaust, fmic, injectors and a fuel pump but has had bigger turbos and other bits pushing horsepower out of it with stock internals.

All comes down to money.

Edited by ecentrix
Maybe I'm just being a bir paranoid about buying a GTR, but I just want one that won't give me any trouble or throw a rod lol.

Now, onto the modifications you can do.

Say if you do a turbo-back exhaust (de-cat), pod filters, boost the turbo's a few pounds higher than factory and install a power-fc, how much awhp should if expect within reason on a safe tune?

My car, in its first incarnation, had pod filters (arguable that these are needed), Apexi turbo-back exhaust, factory cat (why would you de-cat when the factory cat is high flow and legal???), Power FC and a Greddy electronic boost gauge. Everything else was stock. This gave 280 kW at the wheels, with 1.2 bar boost (which is OK on an R34 - normally ran 0.8 bar). It could have been more with a straight-through muffler, but I had a quiet muffler on it. I added a Tomei fuel pump for peace of mind, as the stock one was nearing its limit. (Hard wire the fuel pump, too.)

You can get over 300 kW (400+ hp) with a few more tweaks. The stock FMIC and injectors are fine for such power levels. You will be getting close to the limit for the injectors, but you only need the expense of new ones if you are taking the next step with everything else. Same for the standard air flow meters (which you can take higher, with a tuner who knows his stuff).

But you need to start addressing oil issues, if you ever intend to take it to the track. At the very least you need to have an oil catch can/separator, plumbed back into the sump. (I also had the breather line plumbed back into the intake, which kept it legal.) Consider the Mines cam cover baffles. If you can do it without taking the engine out, get a head drain fitted. If you do take the engine out, as well as fitting anything other than an N1 oil pump (even the stock one is stronger), fit an extended sump and baffle kit (Imports 101 do a good kit :/ ).

Then, an oil cooler and radiator upgrade will help in the WA Summer.

Then … … … … then … … … …

I did say "first incarnation", didn't I?!! :down:

Cheers. :)

No offence but why do you want a GTR if you want reliability and no issues?

There is a good reason they have a bigger engine, twin turbos, thicker sway bars, stiffer suspension, carbon fibre parts, less interior, etc.

Perth of all places, if full of muppets who know sweet FA about what theyre driving, they'll happily thrash the shit out of their cars, but have no clue how to fix it when it breaks - I can safely say this applies to SAU, WA and even a few in this thread. Good luck finding a good condition GTR, with low kms, treated nicely, for those prices.

RE: changing oil pumps as soon as you buy a car ?

...yeah what the f**k? you know how much money that costs (/time it takes if you do it yourself) ?

If something is about to throw in the towel you should be able to pick it up when you see the car running or drive it.

RE: Shipping from over East to here, vehicle carriers like CEVA do have prestige service, where your car travels in a container the whole way, and they use longer run-up ramps or lower vehicles, etc.

it's an extra grand or two...not alot comapred to a $30k-40k car.

My car, in its first incarnation, had pod filters (arguable that these are needed), Apexi turbo-back exhaust, factory cat (why would you de-cat when the factory cat is high flow and legal???), Power FC and a Greddy electronic boost gauge. Everything else was stock. This gave 280 kW at the wheels, with 1.2 bar boost (which is OK on an R34 - normally ran 0.8 bar). It could have been more with a straight-through muffler, but I had a quiet muffler on it. I added a Tomei fuel pump for peace of mind, as the stock one was nearing its limit. (Hard wire the fuel pump, too.)

You can get over 300 kW (400+ hp) with a few more tweaks. The stock FMIC and injectors are fine for such power levels. You will be getting close to the limit for the injectors, but you only need the expense of new ones if you are taking the next step with everything else. Same for the standard air flow meters (which you can take higher, with a tuner who knows his stuff).

But you need to start addressing oil issues, if you ever intend to take it to the track. At the very least you need to have an oil catch can/separator, plumbed back into the sump. (I also had the breather line plumbed back into the intake, which kept it legal.) Consider the Mines cam cover baffles. If you can do it without taking the engine out, get a head drain fitted. If you do take the engine out, as well as fitting anything other than an N1 oil pump (even the stock one is stronger), fit an extended sump and baffle kit (Imports 101 do a good kit :) ).

Then, an oil cooler and radiator upgrade will help in the WA Summer.

Then … … … … then … … … …

I did say "first incarnation", didn't I?!! :banana:

Cheers. :(

280awkw? Thats very good. I would like to see how the car drives. Most 33gtrs I know are around the 250awkw mark give or take with 0.9bar-1.1bar boost.

280kw = 375whp. Thats more than mine makes with all my list of mods at 1.3bar. You ran 1.2bar/17-18psi on stock turbos? Where did you get yours dyno'd?

Say if you do a turbo-back exhaust (de-cat), pod filters, boost the turbo's a few pounds higher than factory and install a power-fc, how much awhp should if expect within reason on a safe tune?

Syfon: Rohans GTR has catback only, pods pfc and running 14psi (1bar) - made 240awhp on that 40deg day at autoworx a while back where everyone elses' numbers were hammered.

Edited by Ten Four

Correction - it was 1.3 bar. My apologies. It was tuned by Steve Thomas using the dyno at Top Racing (in Shootout mode, see attached). This was a good example of what you can get out of a GTR with only a few mods.

Dyno_Graphs_1.pdf (Sorry again - attached wrong graph first time!)

Cheers. :D

Edited by MLCrisis
how safe is 1.3bar?

On an R34, I was reliably informed, it is fine. But probably as high as you would want to go. R34 turbos are steel bearing but still ceramic wheels - but the ceramics were a lot better than the earlier models, where you would not want to go that high.

I'm considering selling my 34GTR at the moment as I'm looking at getting back into my bike racing which I had to give up to enjoy the GTR.

Happy to come show it to see what you think and have a chat about it. Would be be chasing ~$47k for it but would consider offers.

Was bought as Vspec but VIN check shows it as a std GTR, its been fitted with VSpec options though...carbon diffuser and front diffuser.

Has original instrument cluster in it which reads 58800kms at the moment and the condition of the car supports the low mileage.

Fitted with Blitz pods, Power FC, Apexi N1 exhaust...Tuned and Dynoed at Xspeed and then again later when I wasn't happy with the tune at Allstar garage.

I had a 100,000km service completed when I got the car so I could be certain of everything, complete fluid change, belts, water pump, gaskets etc

Top end has been checked by a few mechanics and each has said its clean as a whistle and looks as new.

Recently installed HKS Twin Plate clutch..it was 2nd hand but does the job, it's a little fiddly to get used to the friction point but otherwise fine.

I drive the car almost daily and it's well cared for (had it over 2 years now) and never had a hiccup with it. Will regret selling it but racing is in my blood and I've gotta start thinking about buying a house too.

So yuh...not officially for sale but will happily come and show it to people to give an idea of what a good condition 34 GTR looks like in the flesh and if someone can convince me to part with it...I may well do so.

PM if youre interested in any more details/catching up

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Did this end up working? Did you take some pictures?
    • And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...