Jump to content
SAU Community

[adl] S2 Dayz Front Bar For Sale

webng
 Share

Recommended Posts

webng Experienced

webng

Posted
Posted (edited)

Yes you heard it right, I'm looking at selling off my original Series 2 Dayz front bar for the right price. If I can't get the right price, I'll repair it to replace the Blits Dolphin copy front bar on at the moment and sell that instead as I am still quite fond of the Dayz bar :)

As far as I can tell, apart from the scratches and dents, the 2 main repair jobs are the 2"-3" tear underneath on the right hand side and the mounting bit on the top right, both as circled in the piccys. Will sell with the spotlights, the air vent/scoop thing, and the little bit that came off the mounting bit to be repaired.

Will post interstate if you organise the courier/packaging/pickup etc.

PM me if you want a higher res image to be emailed.

Offers?

Edited by webng
Link to comment
https://www.sau.com.au/forums/topic/318515-adl-s2-dayz-front-bar-for-sale/
Share on other sites
darrinspencer Grand Master

darrinspencer

Posted
Posted

You will need to post a price

You could do everyone a favor and con someone to make a mould for free, so then they could sell them

Do you have decent bodykit shops in Adelaide?

Just an idea

webng Experienced

webng

Posted
  • Author
Posted
You will need to post a price

You could do everyone a favor and con someone to make a mould for free, so then they could sell them

Do you have decent bodykit shops in Adelaide?

Just an idea

Not sure what it's worth. Let's say an instant of $500.

Can the factory plastic bars be repaired?

It's plastic, they can do a lot with plastic as it has memory and they can fuse and weld it nowadays apparently.

32TAXI Experienced

32TAXI

Posted
Posted

Plastic bars can be repaired or modified - I removed no. plate surround and centre section and repaired a few cracks on mine.

Soldering iron to melt and weld, bit of fibreglass to support from rear and bog top, heat gun works well if modifying.

JAV360 Community Regular

JAV360

Posted
Posted

Just bought it, condition isn't that bad, few scratches, side bracket come off and a small ding, nothing unrepairable as its needs painting.

Very rarely do they come up for sale and it saves me damaging my Takero bar that sits 2 inches off the ground.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...