Jump to content
SAU Community

M35 Towing Capacity

Novaz

By Novaz,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Novaz Rookie

Novaz

Posted
Posted

Does anyone know if Nissan has specified a towing capacity for the M35? I have seen various numbers posted from 450kg up to 1900kg, but would like to get some solid info.

I ask because I had the opportunity to score a cheap towbar, for being the first person to have one made and fitted by Best Bars in Auckland. They tested the bar using their test rig shown in the video (note, not my car or the bar I got) -> (

)

I asked them to test the bar up to 1500kg, hoping that I could tow an S13 on a trailer. In the end they only tested it to 1200kg, and weren't comfortable rating the bar any higher 250kg unbraked, 1000kg braked. Their comment was that I would 'get away' with 1200kg loads from time to time, but not day to day.

They said that they could easily make a bar that would handle 1500kg, but in order to use it, the rear end of the car would need reinforcing. They feel that it is quite 'soft' with little underfloor/chassis strength.

I'm a little bit disappointed, but glad I didn't just get one made up locally only to rip the arse off the car.... :D

Link to comment
https://www.sau.com.au/forums/topic/319544-m35-towing-capacity/
Share on other sites
Jetwreck Grand Master

Jetwreck

Posted
Posted (edited)

I don't think it's a great car for towing......I wouldn't like to push it above 1,200kg's non braked or without some kind of re-enforcment in the rear end.

Pretty sure the Ozzy local ones are only good for about 750kg's

Edited by Jetwreck
andy65b Veteran

andy65b

Posted
Posted

The tow bar I have is from Fast fit and is rated to 1250kg unbraked.

I have towed a 7x4 highside trailer with a ful load and 2 windsurfers strapped to the top. Also done another trip recently loaded to the top and 4 bikes on top.

The car tows effortlessly and economy is not that bad if you can keep at a constant pace.

I am not sure that towing a box trailer is any risk to the rear sub frame but I guess it depends on how much weight you load on the tow ball.

But as Duncan said, none of the cars he has seen with a faulty sub frame have tow bars so I am not sure that you can relate this failure to the ability of the car to tow.

Novaz Rookie

Novaz

Posted
  • Author
Posted

Andy, what does your bar look like underneath? Mine is bolted up behind the bumper and has an arm extending part way down the spare wheel well.

I'm wondering if I can get away with towing my S13 (1100kg + trailer, ~1500kg?) The trailer is a tandem axle, braked so can be nicely balanced with minimal draw bar weight.

andy65b Veteran

andy65b

Posted
Posted
Andy, what does your bar look like underneath? Mine is bolted up behind the bumper and has an arm extending part way down the spare wheel well.

I'm wondering if I can get away with towing my S13 (1100kg + trailer, ~1500kg?) The trailer is a tandem axle, braked so can be nicely balanced with minimal draw bar weight.

Mine is bolted across the rear of the car a bit wider than the tailgate behind the bumper. It then has a small tongue that runs under the spare wheel and is bolted there also.

That weight sounds a bit more than I would tow as the tow bar is not the heavy duty kind and I think that would be a fraction too much weight if you had to stop in a hurry.

Cheers

Andy

Duncan Grand Master

Duncan

Posted
Posted

both cracked subframes were are the same place, the main loop between the front and rear mounts, right up at the chassis.

was easy enough to tig up but would be careful with load on the rear of these.

c34 on the other hand have steel subframe not aluminium

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...