Jump to content
SAU Community

Recommended Posts

Hey everyone

Could some one tell me dose a S2 have a dash light control to adjust dim setting on the dash display as I have looked and played with every button I can find but cant seem to find anything

As well I cant see my gear selection lights around gear leaver I guest it dose come with lights or ?

Thanks

Link to comment
https://www.sau.com.au/forums/topic/319835-dash-light-control/
Share on other sites

mine is either dim or off

would love to know if there is any way to brighten it up also, its a great brightness for country roads at nite but useless in the city or any road with street lights

Same goes for my R34GTT, instruments to bright at night, centre consol lights, especialy climate control, way too dim by day, if these are normal, in anotherwise terrific car, WTF were Nissan thinking when they did/didn't do this.

Edited by BASHO
Same goes for my R34GTT, instruments to bright at night, centre consol lights, especialy climate control, way too dim by day, if these are normal, in anotherwise terrific car, WTF were Nissan thinking when they did/didn't do this.

pretty sure my 32 had a dimmer too, or maybe it was my s13 (but may have been aftermarket)

i know that if you put led's in you cant dim them

I am at a loss to understand why Nissan did not fit a dimmer switch.

My R30 has one, and, you can put the electric windows up after the ignition is turned off.

Both those features are well appreciated and must have cost a pittance at manufacture.

pretty sure my 32 had a dimmer too, or maybe it was my s13 (but may have been aftermarket)

i know that if you put led's in you cant dim them

actually its my 31 that has it, dam useful it is too

Has anyone fitted one??? If so how???

I recently read a post on SAU where someone had the steering column covers orf and they found the switch taped up underneath, I immediatly checked mine==nothing however there are a number of vacant sockets under there any of which could be the one, WTF would know --?

My S2 doesn't. But interested in doing it.

Fyi check out the maxima/micra/exa/bluebird(aka sentra) etc in the 94 - 2000 range at the wreckers

dimmer switches are a dime a dozen and all the same, also fits the stag dash socket perfect.

Found my self a fog light switch last week and lotsa blanks to have for spare.

I'm pretty sure many import Nissans don't have it. I think it used to be part of compliance to fit a little pot that would dim the dash. My GTI-R had one that was definately fitted by compliance, but it was imported before all the compliance rules changed. Pretty sure my 260RS doesn't have any dimmer and it was imported after the rules changed.

FYI: I had LEDs installed in my cluster for a short while, and they are far too bright: very distracting when driving, and bright enough to give me headaches when driving more than half an hour at night. I find the centre console birghtness adequate, but believe it could be a little brighter. My Dolphin instrument cluster is the perfect brightness, but unfortunately is backlit in orange, so at night, my dash looks like the Las Vegas strip: orange instruments, blue defis, green console lights, different blue and green on the cd player, and different blue ana orange on the AVC-R.

In contrast, my V35 looks great with its massive stack of orange lights on the centre console, which actually matches (hooray!) the lights in the instrument cluster...

I have not done it yet but it is on the list. My gauges have different colour globes. You can get coloured sleeves to slip over the light. Red, blue and green. So you can have all one colour iin the console instrument cluster.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...