Jump to content
SAU Community

Recommended Posts

Gday,

Ive looked around and cant find

iacspring.jpg

Can someone explain how to access the return spring inside here ?

(this isnt my exact one, took this picture off another site)

Basically i pulled this off my car to clean the valve ect.. and noticed that the tension on the spring wasnt the best.

I am looking at either re-tentioning it, or replacing the spring...............HOW ? -- Because the diaphram doesnt close all the way and i think its causing higher idel (1200-1400 rpm)

I've tried a screwdriver in there to force two bits of the sping apart further... but cant get it enough so i would have to pull it out..

Can someone explain how to remove it ?

Link to comment
https://www.sau.com.au/forums/topic/319849-aac-vavle-spring-aac-internals/
Share on other sites

Yes tried that, but when I took off the solenoid;;; I could not pull the spring/ plunger/ piston out of the aac device.

Used long nose pliers to no avail,

I was thinking perhaps the other side,

there seems to be some kind of cover and the spring stuff it moulded in there. - it may also just be a sticker,,

can you confirm if I just use more force it will slide out ?

Cheere

Yes tried that, but when I took off the solenoid;;; I could not pull the spring/ plunger/ piston out of the aac device.

Used long nose pliers to no avail,

I was thinking perhaps the other side,

there seems to be some kind of cover and the spring stuff it moulded in there. - it may also just be a sticker,,

can you confirm if I just use more force it will slide out ?

Cheere

Im right with you on this also. I was considering picking out the brown filler that is in there that seems to hold it all in. I think my spring is also weak and needs replacing. My idle is pretty crap, ECU just doesnt seem to take control of it very well.

I have a lathe. I was even thinking of putting my valve in the lathe and carefully "turning" out the brown stuff.

At the end of the day, it would probably work out faster and easier to get a whole other assembly from a wreckers for ~ $100-150, rather than playing with that one.

I'm all for the DIY route and will try wherever possible to repair parts, but some times you have to just admit defeat haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You know how your car rolled through a fence in your last jacking escapade? Scissor jacks increase the likely hood of that sort of thing happening immensely!
    • http://calfinn.com.au/product/1500kg-standard-trolley-jack-cj-2t-c/1500kg-standard-trolley-jack-cj-2t-c   I have this and fits under a S3 33 GTR with no issues. Purchased in 2009 and not one issue. It was $950 back then. Not cheap but something so important isn’t worth cheaping out on.
    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
×
×
  • Create New...