Jump to content
SAU Community

Recommended Posts

-For sale is brand new in box 86.5mm CP piston set for RB26. Compression ratio is standard 8.5:1

Comes with all rings, gudgeon pins, clips and exact setup measurements.

Looking for $1100 ono. Look around you will not buy these in Australia for this price.

RB26 CP pistons

-Full complete RB26 head without rocker covers reshimmed recently

Looking for $1300 ono

-RB26 R32/33 GTR power FC PRO with hand controller. Yes the one with launch control and ignition rev limiter

$1500 (i really don't want to part with it but it is not being used)

R33 GTR fuel pump 60,000km

$150

R32 GTR front diff and sump complete

$300

RB25/26 head external oil drain kit

$120

RB series head drain

Contact Ben on 0401 779 905 for any other questions

Edited by BK
Link to comment
https://www.sau.com.au/forums/topic/320231-rb26-head-r32-gtr-sump-power-fc-pro/
Share on other sites

  • 3 weeks later...

Price drop

$1000 for cp pistons

$1100 for head

$120 R33 GTR fuel pump

$250 GTR sump

Power FC pro + Hand controller - make an offer

  • 2 weeks later...
  • 2 weeks later...

Sorry about that. Drain kit is sold pending payment. Rest is still available at:

$1000 for cp pistons

$1100 for head

$120 R33 GTR fuel pump

$250 GTR sump

Power FC pro + Hand controller - make an offer !

Have to offer more than that for me to let go of the Power FC Pro. They are not very common. Also everyone asking if the Pro unit is d jetro/MAP sensor based the answer is no. You need to run Airflow meters. Following still for sale :

$1000 86.5mm cp pistons + rings - FIRM PRICE

$1200 OS giken R3C triple plate

$120 R33 GTR fuel pump

$250 GTR sump

$1300 Power FC pro + Hand controller

Edited by BK
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...