Jump to content
SAU Community

Recommended Posts

hey guys

for the past couple of months my car has been making an immensly loud squeel on start up, only when cold and i wasnt too worried about it at the start but on a drive home last night it happened while i was driving so im concrned now.

i managed to get the bonnet up and someone else to start the car and from the looks of it none of the two belts are slipping, and the screeching noise sounds like its comming from the opposite end to those belts.

a bearing maybe?

any ideas on how to fix this would be beautiful!

Callum

Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/
Share on other sites

CRC or silicon spray all the bearings etc that the belts run on. I usually do it every now and again even tho its never happened to me

ive siliconned sprayed all the bearings i could get to, so ill post back if it did anything or not.

it just doesnt seem though like its comming from the front of the engine, it sounds like

sh*t i hope this isnt serious

Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5234916
Share on other sites

Bearings will make noise all the time if they're stuffed. More likely to be belts - have you checked the tension? You can probably tighten them up again if they're loose, but if it were me i'd just replace them if they dont look perfect.

Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5234995
Share on other sites

From personal experience, i would be looking at the alternator belt in particular.

the screech on start would be the alternator kicking in and trying to charge the battery as quick as it can due to the charge lost when cranking. then usually the alternator starts spinning/ the regulator tames it down and the screech stops.

there should be the correct tensions and where to check deflection in the engine manual that's floating around.

oddly enough though, i currently have the opposite problem. at high rpm (4500+) i get a screeching and i have no idea what it is.

Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5235292
Share on other sites

Just for the record, a lot of of old jap cars/vans like the nissan vanette etc squeal on start up and idle so it cant be too serious, just something small that bosses cant be f**ked paying for to be replaced lol.

I only mentioned lubing the bearings as iv heard mine starting to squeal while idling, probably got dust etc in them and the lube they would have had (if serviced properly) has dried up which would cause a squeal until they start moving.

Try all the small things first so you can eliminate the problem before spending money on unneeded repairs/parts, ring a local mechanic and ask him what the common causes are of squealing and you should get a few answers pretty quickly

Edited by R34 -_-
Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5235689
Share on other sites

From personal experience, i would be looking at the alternator belt in particular.

the screech on start would be the alternator kicking in and trying to charge the battery as quick as it can due to the charge lost when cranking. then usually the alternator starts spinning/ the regulator tames it down and the screech stops.

there should be the correct tensions and where to check deflection in the engine manual that's floating around.

oddly enough though, i currently have the opposite problem. at high rpm (4500+) i get a screeching and i have no idea what it is.

Haha.....I got both problems...fixed the second one,

wasnt to worried about the first,

though it is annoying when everybody keeps telling me to tighten my fanbelt...

Edited by Arthur T3
Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5235884
Share on other sites

alright cheers

my belts all seem to be fine and intact, no wear on them, i also got a rag and wiped them down to eliminate any possible fluids on them

the only thing is it squiels while its cold, once the engine is at opetating temperature, if i turn the car off and on again no squeal occurs

i thought it may be a possible belt thats too tight? considering its happening when its cold and not when it hots, the old saying heat = expansion? could this be possible also?

Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5235887
Share on other sites

  • 3 weeks later...
had a look at the engine yesterday, noticed some major slackage on the alternator belt, so tighten that up and bam. no squeel!

my only question is, how do i stop it from becoming loose again?

Once you have tightened the tensioner bolt just tighten the lock block bolt. Just make it hand tight. No need to over do it with a 25 foot torsion bar. The bottom main pivot bolt only needs to be reasonably tight.

The belt squealed when the engine was cold until the belt warmed a bit and gripped better.

Nigel

Link to comment
https://www.sau.com.au/forums/topic/320725-squirl-mincer/#findComment-5278957
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...