Jump to content
SAU Community

Recommended Posts

Hi Guys,

Selling my Series 1 R33 Gtst, 1993 model Skyline. I'm the first Australian owner, have had the car for a little over 2 years. Someone backed into the rear quarter, so it still has some damage. Also the drivers door and guard need some paint work. Basically the whole drivers side of the car could do with a respray. The front bar and bonnet need some attention too.

It has roughly 120,000 klms on the clock. I haven't had any mechanical issues with it at all, except for when I first got it the coils needed replacing - runs extremely well.

Registration ran out on 18/05 and I'll be selling it unregistered with no rwc. It shouldn't be too hard to re register, take the boost controller off and the pod filter maybe, that's probably all it needs.

It hasn't had too much work done to it, it has the following mods:

Splitfire Coils

Exhaust from turbo back

R34 side mount intercooler

Pod filter

18' XHP Wheels - tyres around 60% tread. All wheels have gutter rash.

Manual boost controller - pretty much turned down.

Timing belt was replaced with a Gates timing belt at 109,000 klms in September 08. Since then, it has been driven from Sydney to Melbourne and has only travelled 11000 klms including that drive.

It has an Alpine CD & Tape player, with alpine speakers all round including tweeters.

It has the original skyline floor mats

I had bought another boot with drift wing from someone on here, but the fktard couriers dropped it I think ( see photo's). Will include the boot. Also will include the stock R33 side mount intercooler.

There are a couple of cracked hoses in the engine bay - you can probably see my dodgy tape up job. I'll be looking at getting them replaced.

The car hasn't been thrashed, it barely gets driven at all unfortunately.

Looking for $5000 for it. I was quoted about $1000 - $1500 to fix the damage and respray, but that was in Sydney. I don't really have the spare cash or the time to do it, so I've decided to sell it as I need a van for work.

I can be contacted on 0458 333 444 or by PM.

post-60124-1274317532_thumb.jpg

post-60124-1274317550_thumb.jpg

post-60124-1274317565_thumb.jpg

post-60124-1274317590_thumb.jpg

post-60124-1274317618_thumb.jpg

post-60124-1274317632_thumb.jpg

post-60124-1274317693_thumb.jpg

post-60124-1274317717_thumb.jpg

post-60124-1274317734_thumb.jpg

post-60124-1274317744_thumb.jpg

post-60124-1274317754_thumb.jpg

post-60124-1274317772_thumb.jpg

post-60124-1274317787_thumb.jpg

post-60124-1274317800_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/321383-wrecking-r33-gtst-series-1/
Share on other sites

the title says your wrecking it but the post says your selling it whole?

If your wrecking it how much for the front bar and bonnet?

Location?

Edited by W0rp3D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...