Jump to content
SAU Community

Recommended Posts

Hello all

Want some advice recently my 95 R33 GTs25t has been giving me starting issues, dosn't do it all the time

sometimes it takes 2 - 3 goes before it starts, sometimes it takes a long time to start and

then when it does start up the revs drop right down and it nearly stalls before revving back up to normal again

once its started it drives fine.

Iv'e been looking at a few things and was wondering if the coolant temp sensor

would cause this, I have noticed lately that after a 40min drive my cars temp gauge is still showing that its cold

the gauge does move up from the first stroke but it dosen't quite reach its normal operating temp by the guage,

which I think is wrong as the car would have been definetly warmed up after a 40 min run, I have been to various places

to check this starting issue and they hook it up to the scope and such and no errors come up at all, they find nothing wrong with it

and I have heard that the coolant temp sensor will not show up any errors, also another thing could it have anything to do with O2 sensor

as far as I know this has not been replaced and I know a lot of people replace this at 100,000kms the CAS has been checked and it seems fine

I'm taking it in tomorrow for its 130,000km service hopefully they find something and fix it

Just wanting to know what it could be so that when I take it in I can get them to check it.

Any help on this would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/321774-r33-coolant-temp-sensor/
Share on other sites

Is this a "hot start" issue, or a "cold start" issue, or both?

If the engine isn't getting up to normal temp, and also takes a long time to get up to temp (approx 5 minutes gentle driving should see the engine at normal temp), then it is possible the thermostat is jammed part open, and needs replacing.

To test the gauge is working correctly, set the key to IGN, disconnect the wire onto the (single-pin) temp sensor, and ground it out on the engine - the gauge should go full-scale if it is working correctly.

NOTHING TO DO WITH THE O2 SENSOR! It only works for cruise conditions.

I'm fairly sure its a hot start issue as when I start it first thing in the morning it starts up fine,

and when I start it to go home from work it starts up ok, it generally has the issue after I get home from work

I'll leave it for about half hour - hour then when I get in it to start it up to go out again it plays up,

and regarding the heater I don't reckon it gets as hot as much as it used to, so it might be the thermostat playing up

I'll have to check that out

thanks for the reply guys.

Well, according to the workshop manual, difficulty warm / hot starting could be related to the (ECU) temp sensor. Try disconnecting the sensor, see if it makes any difference. Check the resistance of the sensor. Check its output voltage.

Can also be a fuel pressure problem. Try clamping off the fuel return line, see what happens.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just trying to get my head around this. At 5psi of boost, you turn on your wmi pump, and then you're using a 3000cc injector, to allow flow upto the actual engine, where you have your 6x200cc injectors and a 500cc injector. If the above is correct, what advantage are you obtaining by having the 3000cc injector blocking flow, is this just incase a line breaks between that injector and the motor you can stop flow immediately? Or are the 6x200cc and 500cc less injectors and just spray nozzle?
    • Welcome! New member myself, but I had an R33 back in 2002. Best advice I could give, based on my experience: if you're running the factory turbo, be very conservative with boost. I made the mistake of just fiddling around with the boost controller and cranking the boost for fun, and the end result was my intake pipes popping off frequently from the constant deluge of oil that was being blown into the recirc by the stressed-out turbo, which itself was siphoning oil from the engine and farting it out both sides of its centre bearing (or something to that effect). If I could do it all again, I would have gotten a new turbo and had a tune dialled in professionally and then just left it alone! Funny you mention the metal shavings in the gearbox, as I had the same thing - the probe plug (magnetic drain plug, essentially) would come out caked with shavings. At least it was doing its job. Not sure if that's just sacrificial wear and part of the deal, or if my gearbox was shagged, but I wasn't abusing it. Enjoy the R33 - they're a dying breed, and if they weren't $35k+ on CarSales in Queensland, I might have picked up one of those again, instead of the 370GT I own now (though I'm loving the 370GT, that big 3.7L V6 just hits different).
    • Howdy folks. I owned an R33 back in 2002, which was thoroughly beyond my capacity (financially speaking) to maintain/insure, so we parted ways in 2004. Fast forward 21 years (to literally yesterday, in fact) and I'm now the proud owner of a 2007 V36 370GT. I'm happily surprised by how much power the VQ37VHR makes, compared to the RB25DET, considering the latter is turbocharged. I had planned to add a turbo at some point but I'm on the fence about whether I'll even need it (though I do love the sudden onset of extra torque). Any other 370GT owners around the traps, I'd love to hear about your experiences with this car (good and bad).
    • Perhaps the answer is... more jacks!* *proper jacks must be used.  
    • I NEVER think about using a scissor jack unless there is absolutely no other alternative. f**king things are dangerous, annoying and stupid.
×
×
  • Create New...