Jump to content
SAU Community

Recommended Posts

post-9688-1274928735_thumb.jpg

NOTE: THIS IS A 4WD MAINLINE 1200HP DYNO, 2WD & 4WD CARS CATERED FOR!!

Entries are limited, PM myself or contact Nick on the details listed in the flyer above.

Hope to see you all there!

Should be plenty of 300rwkw and 400rwkw cars in attendance! May even see 500rwkw+ :bunny: .

Cheers.

Ben

Edited by tas_180
Local 500rwkw cars???

I'd better step it up a notch for the re-build then.

Ha ha..

Justin.

I think 510rwkw is the most so far, not bad considering he's been open a month haha!

RB26 with GT4294R will be tuned next week, should go alright :(.

It says 3 dyno runs, are these consecutive? Can you make adjustments inbetween? (aka a low and high boost run)

Yes consecutive.

Boost adjustments are fine :(. No major adjustments though as time for each car is limited (to ensure everyone gets their go).

Cheers.

Ben

Yes consecutive.

Boost adjustments are fine :(. No major adjustments though as time for each car is limited (to ensure everyone gets their go).

Cheers.

Ben

Uh ok no worries. I just wanted a low boost (Daily) read out, and a high(er) boost (with water + methanol injection) read out, 10 sec job.

Ta,

I think 510rwkw is the most so far, not bad considering he's been open a month haha!

Oh Crap... What was that???

RB26 with GT4294R will be tuned next week, should go alright :yes:.

... Yeah I don't know if I'm THAT keen. hah a ha.

The guy needs a T-Shirt.... "GOT LAG?"

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
×
×
  • Create New...