Jump to content
SAU Community

Recommended Posts

  • Replies 260
  • Created
  • Last Reply

Top Posters In This Topic

For ppl that might be interested in a pre xmas or new year meet, let chuckie know. :thumbsup:

My suggestion is churchman brook dam. Nice roads and bbq facilities. Even seen a few evo clubs out there.

Churchman Brook dam

Good drive, I'm in pending dates.. things get pretty hectic in the silly season :/

:stupid::w00t: how do i get told ,Fu-k the walk up there ,weekend`s it`s PACKED OUT Jason,you need to go up lateish if your hoping to get spot as it`s full till abut 3 pm ,or you need to pop passed & have a look dude,
  • 2 weeks later...

+1 on dont fkn bother on a weekend. Wungong dam is a bit more spread out, and has better carparks. :thumbsup: Plus, if you have a meet point in Kalamunda, I can show youse all my favourite drive through the top of the scarp. Only problem is, the longest straight is only about 200m, so the chances of all your lumbering lolvo's keeping up with the sheer might of Teh Fury is pretty low.

:P

*edit - :3some:

Only problem is, the longest straight is only about 200m, so the chances of all your lumbering lolvo's keeping up with the sheer might of Teh Fury is pretty low.

Is that a challenge? :banana:

  • 2 weeks later...

just dont ask him to pull his shaft. some ppl get really weird about that on here. lolz

I see what you did there :P

Anyways, let's throw some dates around so we can all gauge interest and work out a day that most of us can make it!

A lazy Sunday towards the end of the month/early feb is my suggestion :)

two weeks ppl. bbq dont know where yet nth or sth. :cheers:

possible list, pretty sure we have all color stags covered:

mitsterbrau

chuckie

bubba

horrace

appealing?

d1_drifter?

Big Jim?

Odddyman?

blizzerd?

darq?

260rsstagea?

RS444?

ssshonky?

unique1?

.....and of course dale ( leave teh fury @ home for the mrs and get a lift in a real car.) lol

Edited by dirtyRS4

WOOOOOoooooow... It's been so long since i have been on here... And Chucky, you will be happy to know that i have decided to keep the Staj after that convo we had when you dropped off the intercooler ;)

I WOULD BE SO UP FOR THIS! So long as you don't mind me bringing my half beaten up Staj (Due to some ass clown hitting me and pushing me around with a bull bar).

I'll also bring the camera if any of you want shot's?

I'll make time for this! I believe that you are all thinking the 16th now? Glad i logged on now then!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...