Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

hey luke!

do you by chance have the squishy rubber hose that goes from the front turbo inlet elbow to the air flow meter/airbox? - think i can see it in the box in that pic you posted up

also wondering if you have the following hose?

http://www.skylinesaustralia.com/forums/post-a286350-

"14463MG" in the image.

oh, and a stock rear turbo oil drain? ;) AHEM.

If it's in the box Nigel ur welcome to it. Best to come down and have a look. I'm going all alloy piping so getting rid of all the rubber stuff I've got.

Luke

Whole list of parts for sale from my 1999 R34 N/A GT-four sedan.

Front seats $200 pair with rails

Rear seats $150

All seat belts $200

Parcel shelf with 4 tweeter holes cut out $50

Roof lining in black velour $150

All pillars in black velour $60

Fuel tank $250

Front bar $200

Front guards $ 200

Bonnet (couple of stone chips/pin dents $250

Bonnet latch $50

Bonnet hinges $50

Cusco Master cylinder stopper $80

Glove box $50

Kick panels $80

Door Trims $100

Cusco Full bolt in cage $1200

Brake master cylinder $120

R34 GT-four gear box, Small crunch 3-4. Chuck some redline in and she'll be right, Complete manual conversion $1200 Will include clutch master, pedal etc

Clutch pedal $120

Clutch master $80

Brake pedal $50

Accelerator pedal $50

R34 N/A brakes complete set, discs, calipers, lines $300

R34 N/A air box $50

All Air con stuff $200

Brake lines $50

Heater box (non leaking) $150

ABS module $150

Climate control display $150

Bnr34 brembo's low k's, slotted rotors, A1RM pads, braided lines, complete set $2800

R34 Rear hubs, handbrake set-up, handbrake lever, lca, $300

If your after a stock part that isnt there let me know.

Will be adding more as i think of it.

Cheers Luke

Hi there i'm after the hazard light switch for my r34 gtt sedan. Have u got it if yes for how much including postage to 3073.

Cheers :laugh:

hey mate your front bar standard?

sure is mate. It's got the factory fog light holes but the brackets were all rusted so took them out. Also got the little antenna in the front passenger area, but doesn't work anymore.

Also keeping the hazard thing as I may need it.

Edited by Luke_ENR34
  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...