Jump to content
SAU Community

19" Work Euroline Wheels For Sale

n15m0
 Share

Recommended Posts

n15m0 Grand Master

n15m0

Posted
Posted

Hi All,

My wheels are up for sale:

Work Euroline FE

19x8.5 +43 (32mm dish)

19x9.5 +38 (73mm dish)

5x114.3

Wheels only. Had them on my V 35 sedan running 275s on the rear and 245s on the front. They are a 2 piece wheel with anodised lip and machined face.

Excellent condition, no gutter rash whatsoever. Very close to brand new.

Asking $2500 ONO.

Will fit most Nissans or Toyotas too...previously was on an Aristo.

Pick up southside Brisbane prefered and inspections welcome for serious buyers.

IMG_4206.jpg

IMG_4223.jpg

IMG_4210.jpg

IMG_6900.jpg

IMG_6898.jpg

Thanks for looking! :)

Link to comment
https://www.sau.com.au/forums/topic/322828-19-work-euroline-wheels-for-sale/
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...
  • 3 weeks later...
  • 3 weeks later...
  • 3 months later...
  • 3 weeks later...
Blackzedder Apprentice

Blackzedder

Posted
Posted

I would make an offer but I'm not sure about the offset on the front. I have a V35 coupe which has +30 offset but I think the sedans have +45 or thereabouts. I may not have enough clearance on the inside of the wheel to suspension.

If you know they will fit let me know. 0418798165.

Cheers

  • 3 months later...
n15m0 Grand Master

n15m0

Posted
  • Author
Posted

Hi RuZoo,

I'm glad someone is finally interested in these fine wheels. Obviously you have good taste and these will look really good on your Supra. I do not normally post overseas but I will make an exception this time.

I have checked up on postal charges to Chile today. They are the same price as posting to Nigeria as I have previously done. Postage to Chile will be $1400 AUD. This includes insurance as well so the wheels will be covered. I will also need to pack these wheels properly so they do not get damaged. Handling fee will be $500 AUD.

So in total:

Wheels - $2000AUD

Shipping - $1400AUD

Handling - $500AUD

$3900AUD in total which is equal to approximately $4163USD at todays fantastic exchange rate.

If you are happy with the above, please let me know and I will send you my bank details for direct bank transfer.

Hope to hear from you soon.

:cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...