Jump to content
SAU Community

Where To Go To Get Oil Cleaned Off Engine?

brad20

By brad20,
in South Australia

 Share

Recommended Posts

Import S13 Veteran

Import S13

Posted
Posted

grab some degreaser for a couple of bux, cover the spot in degreaser and watch is fall out.

may need to rub some off depending on the quality of degreaser or how bad the oil is on there but 9 times out of 10 itll just fall off.

dont get the stuff on your electrics and itll be fine

brad20 Apprentice

brad20

Posted
  • Author
Posted

All good and well if you can easily get under your car but since my car sits 100mm off the ground it makes things a little difficult to see what the hell is going on. If I could hoist it up and get under it with some light it would be a different story. CBF and I just want to get someone to do it for me properly

Import S13 Veteran

Import S13

Posted
Posted

yeah my mechanic did mine once for me.

also to help with low cars, my old car sat lower then yours and my drift car rides chassis rails trying to get up anything and all i did was put the car on car ramps (using small planks of wood as a step up) and rolled under it and went to town on it with degreaser.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...