Jump to content
SAU Community

Recommended Posts

Ok guys im looking into to turning my skyline into a a full drag set up so im looking at selling me twin turbo set up thats on my r33 gtst ,its a twin 3037 with .8 or .6 rear housing ,which ever you would like ,it will come with everthing you will need ,as im looking at going to somthing like a gt4508 ,

so it will come with 2 gt 3037 with .6 or .8 housing ,mainfolds dump pipes .a full twin 3 inch exhurst 2 air cleaners and intake pipes ,a twin entry 105 mm thick blitz intercooler ,2 turbo blankets ,also twin screamer pipes with 2 tail 38mm gates all the water lines and and oil return lines ,allm nuts and bolts ,

all the goods are still on the car so if you would like pix thats no probs ,the car is running 488.9 rwkw with this set up on it with a man and on pump fuel with 23 psi ,the turbo have had very little use only run in time on the motor and 8 passes down the strip.

all parts will be sent from Townsville Qld 4818

and im looking round $5000, ono

if anyone would like pix pm me a e mail address and e mail some pix .

cheers

Link to comment
https://www.sau.com.au/forums/topic/323651-twin-turbo-set-up/
Share on other sites

Ok guys im looking into to turning my skyline into a a full drag set up so im looking at selling me twin turbo set up thats on my r33 gtst ,its a twin 3037 with .8 or .6 rear housing ,which ever you would like ,it will come with everthing you will need ,as im looking at going to somthing like a gt4508 ,

so it will come with 2 gt 3037 with .6 or .8 housing ,mainfolds dump pipes .a full twin 3 inch exhurst 2 air cleaners and intake pipes ,a twin entry 105 mm thick blitz intercooler ,2 turbo blankets ,also twin screamer pipes with 2 tail 38mm gates all the water lines and and oil return lines ,allm nuts and bolts ,

all the goods are still on the car so if you would like pix thats no probs ,the car is running 488.9 rwkw with this set up on it with a man and on pump fuel with 23 psi ,the turbo have had very little use only run in time on the motor and 8 passes down the strip.

all parts will be sent from Townsville Qld 4818

and im looking round $5000, ono

if anyone would like pix pm me a e mail address and e mail some pix .

cheers

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

You change your mind more than I do. lol

Just lean on the boost a little and tune it for E85.

What times have you run with this setup so far...?

Goodluck with the sale

LOL ive only ran 10.4 @ 136 mph on pump fuel ,i would love to go e85 but its to hard to get to townsville Qld ,so im just going to use roo 16 ,but im still not sure yet ,if i can sell the whole set up i will go to single cause i was thinking about trying the water to air cooler as well .

have you got your car running yet ?

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

post-51182-1275820741_thumb.jpg

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

Mate ill see if i can pull the front bar off and take a pix for you ..if you like

You change your mind more than I do. lol

Just lean on the boost a little and tune it for E85.

What times have you run with this setup so far...?

Goodluck with the sale

LOL ive only ran 10.4 @ 136 mph on pump fuel ,i would love to go e85 but its to hard to get to townsville Qld ,so im just going to use roo 16 ,but im still not sure yet ,if i can sell the whole set up i will go to single cause i was thinking about trying the water to air cooler as well .

have you got your car running yet ?

Had it running and tuned but didnt make it to the track. Is in parts again but am building a house now so the toys have to wait a few more months.

Could you get a few 205 drums of E85 sent up to townsville...?

You change your mind more than I do. lol

Just lean on the boost a little and tune it for E85.

What times have you run with this setup so far...?

Goodluck with the sale

LOL ive only ran 10.4 @ 136 mph on pump fuel ,i would love to go e85 but its to hard to get to townsville Qld ,so im just going to use roo 16 ,but im still not sure yet ,if i can sell the whole set up i will go to single cause i was thinking about trying the water to air cooler as well .

have you got your car running yet ?

Had it running and tuned but didnt make it to the track. Is in parts again but am building a house now so the toys have to wait a few more months.

Could you get a few 205 drums of E85 sent up to townsville...?

yeah but cause its dangerous good its ex to ship thats all ..and i didnt no you could buy it in 205 ltr

Couldn't reply to your pm, I haven't been enough of a post whore yet. I'm chasing sponsors at the moment, it all depends on which one bites first. That said, I have a better chance than most in this area, though I won't rant on about why. It's a bit is a "how long is a piece of string?" question, could be this week, could be a few weeks away. If you don't want to wait then I understand. I'm sure I'm not the only one looking for this sort of set-up.

Hi,

I am looking for a 100/105mm twin entries intercooler for cercuit work.

I have got a near new Trust 130mm FMIC taken off a GTR33 with T88-34D rated at 900hp 44mm HKS waste gate manifold front pipe etc. for compliance and rego. In storage, no shaft play at all. ( power run dyno at 355kw all 4 untouched from the dock, should be a lot more)

I also have another T88-38GK rated at1200hp with 48mm gate and all the set up dyno at 455kw at all 4 22psi on pump fuel. Engine being refreshed ATM.

Building a time attack GTR33 now. will be using -5 and HKS 2530 for the respond.

If you don't mind to send me pic of your set up, mainly the Blitz cooler. ( prefer ARC twin entries 100mm if any body got one to sell or swap) will consider your Blitz if you end up seperating

email [email protected]

Alex 0433 878905

Mordialloc Vic 3195

www.jds-auto-imports.com

Hi, I have got a PWR water to air cooler,with pump and seperate radiator,etc which I have not even tried yet.It is here for my S15 but it has a good ARC already and will be re tuned to E85 in RE Custom tomorrow then will track test the whole set up in Sandown and Phillip Island.If we end up getting around 300kw at wheel, I don't need to use the PWR.

  • 2 weeks later...
how hard would this be to adapt to a rb26

The water to air heat exchance tube can be mounted anywhere handy to feed cooled air to intake and the little water radiator and electric pump can be mounted like a oil cooler in front of normal radiator.

May put this device into a Hiace turbo diesel ( no room for normal air to air cooler with piping) to see what gain it achieves.

Would like to swap an ARC twin entry for curcuit work.

post-50742-1277028627_thumb.jpg

post-50742-1277028637_thumb.jpg

The water to air heat exchance tube can be mounted anywhere handy to feed cooled air to intake and the little water radiator and electric pump can be mounted like a oil cooler in front of normal radiator.

May put this device into a Hiace turbo diesel ( no room for normal air to air cooler with piping) to see what gain it achieves.

Would like to swap an ARC twin entry for curcuit work.

the water to air i was looking at doing was a pwr or a plazman .and just run a ice box instead with water and a pump instead of the radiator ,so i can keep temps down while at the drag strip.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...