Jump to content
SAU Community

Recommended Posts

Ok guys new to the forum heres my daily/track hack. Its an 88 model Cefiro with most of the luxury featurs either not working or disconnected... Mod list:

Button clutch

Mines ECU

Monkey warehouse fmic

Alloy radiator

NISMO 17x8.5 +35 rims with bulk spacers

Pair gtr teks

Hks podfilter

Buddy club coilovers

Gtr swaybars

Adjustable rear camber arms

Adjustable castor rods

3inch exhaust with twin 3" straight pipes

Leaky screamer

GReedy temp gauge, boost guage

Oil catch can

Shimmed diff

Walbro 550hp fuel pump

Standard BB Turbo

Splitfires

Bride drivers

Dildo shifter

Strobes

HKS turbo timer

Blitz SBC boost controller

Suede steer with OMP button

Just need a z32 then tune with 570cc Siemens injectors and adjustable cam gears. Will be looking at 200rwkw on around 1 bar. Also need to fit half cage I have lying around.

P31602641632x1224.jpg

P5160019.jpg

photo-5.jpg

P5160018.jpg

or57oo.png

2wrkorr.png

2po15x4.png

wslgcx.png

Skid pics!

4620718835_fbff1e91de_o.jpg

post-183839-1274220841799354988.jpg

post-183839-1274220841646424489.jpg

post-183839-1274220841611868391.jpg

post-183839-127422084192017359.jpg

dsc0440ww.jpg

dsc0387b.jpg

post-175076-12742330261660481521.jpg

Want:

s2 tail lights

5 stud

Gauges

More suspension goodies

Let me know what you think!

Edited by surfbum64
Link to comment
https://www.sau.com.au/forums/topic/323972-my-a31/
Share on other sites

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 weeks later...
  • 3 weeks later...

Ok so havnt updated for a little bit haha

Bought a pair of 16x10 works and now have my gtr teks on the front with 20mm spacers

Also got a major service done and put aircon in (not working yet)

But thats about it.

New fitment

P72500621224x1632.jpg

P72500631632x1224.jpg

Link to comment
https://www.sau.com.au/forums/topic/323972-my-a31/#findComment-5373522
Share on other sites

  • 2 months later...

Been a few months since I have up dated this.

Now has Kei office coilovers all round, half cage is in, weathershields fitted, roof wing fitted, new nardi and bought a 33gtr passenger seat.

5 stud is going in next weekend, hope to have rear toe and traction arms next weekend and get new wheel alignment.

Also need more wheels for 5 stud sigh...

Polished works, which are for sale you should buy them so i can get new wheels :)

P80200901077x808.jpg

Link to comment
https://www.sau.com.au/forums/topic/323972-my-a31/#findComment-5501210
Share on other sites

  • 2 weeks later...

5 stud is in, finally got toe arms and good wheel alignment

still running a bit too much camber in the rear due to big tyres but it is friendly to the diff

swapped the works for some P1s and it now looks like this

IMG_0763855x639.jpg

am doing a sprint session this saturday with a group of mates hoping for a resonable time

let me know what you think!

Link to comment
https://www.sau.com.au/forums/topic/323972-my-a31/#findComment-5521106
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...