Jump to content
SAU Community

Recommended Posts

Yawn. So much prefer to be asking tech questions to get more power or handling....but anyway. My daily GTR's heater doesn't run hot enough. Cold Melbourne mornings over-run it. Says 32 on the dash display but I'd think the heat is equivalent to 24 at best.

In all other respects the heating cooling ventilation is working as you'd want.

Any ideas on a fix other than replace the 'head unit'?

Link to comment
https://www.sau.com.au/forums/topic/324009-r32-gtr-cabin-heater/
Share on other sites

not sure if it's the same system as the early 180sx's (mine was 1989 same era as the R32's) but there was a way to get into the diagnostics for the climate control and you can set a bias for the temperature sensor.

the idea would be to make it think it's only 16C when it is actually 20C and therefore it will try to heat more (for example).

somewhere on this forum should be a post on how to get into the diagnostics. also make sure that the temp sensor in the cabin is plugged in and mounted correctly. there should be some small slits somewhere around all the other controls on the dash, thats the intake for the sensor. it should have 1 plug and 1 small (wide as a thumb) tube coming off it.

hopefully that helps.

close outside vent then turn all way up once it is all the way up push and hold the hot button till "FH" comes on, the same can be done for cooling with "FC" appearing on sceen

OK, I stumbled across FH last week but couldn't do anything with it. When you say 'outside vent' what do you mean? Where is this located and how do I close it. Forgive me if this is just a dash vent as that would be a stupid question eh... eh. Also, what is the effect of doing this please? What does it achieve?

It's possible the actuator rod isnt completely opening up, do you get cold air in summer or only cool air?

Good question. In summer with the AC on, it doesn't blow as cold as you think it should. The car was fairly recently imported last summer so I'll assume the AC was de-gased / re-gased and therefore this part of the AC function is OK. Perhaps this points to your diagnosis......Fan only cold is hard to judge as everything is too hot in summer and too cold in winter, when set to 18 degrees.

So, let's say it's the actuators, how do you fix these? Where are they? More to the point, to what kind of person do I take it to for fixing as I'm not the type (unfortunately) to get my hands dirty.

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

paper trick?

OK, I stumbled across FH last week but couldn't do anything with it. When you say 'outside vent' what do you mean? Where is this located and how do I close it. Forgive me if this is just a dash vent as that would be a stupid question eh... eh. Also, what is the effect of doing this please? What does it achieve?

sorry my bad i meant turn it to recycle air not bring it in from outside

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

mine has this problem but if i put my finger on the electrical plug at the bottom of the unit and push up the unit works while my finger is stiil pushing

I do the exact same thing, in summer i push that plug up to do to full cold, in winter i do the same to get it to full hot position. Ive got long enough arms to be able to do it while driving, though i prefer doing it at lights

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...