Jump to content
SAU Community

Recommended Posts

Yawn. So much prefer to be asking tech questions to get more power or handling....but anyway. My daily GTR's heater doesn't run hot enough. Cold Melbourne mornings over-run it. Says 32 on the dash display but I'd think the heat is equivalent to 24 at best.

In all other respects the heating cooling ventilation is working as you'd want.

Any ideas on a fix other than replace the 'head unit'?

Link to comment
https://www.sau.com.au/forums/topic/324009-r32-gtr-cabin-heater/
Share on other sites

not sure if it's the same system as the early 180sx's (mine was 1989 same era as the R32's) but there was a way to get into the diagnostics for the climate control and you can set a bias for the temperature sensor.

the idea would be to make it think it's only 16C when it is actually 20C and therefore it will try to heat more (for example).

somewhere on this forum should be a post on how to get into the diagnostics. also make sure that the temp sensor in the cabin is plugged in and mounted correctly. there should be some small slits somewhere around all the other controls on the dash, thats the intake for the sensor. it should have 1 plug and 1 small (wide as a thumb) tube coming off it.

hopefully that helps.

close outside vent then turn all way up once it is all the way up push and hold the hot button till "FH" comes on, the same can be done for cooling with "FC" appearing on sceen

OK, I stumbled across FH last week but couldn't do anything with it. When you say 'outside vent' what do you mean? Where is this located and how do I close it. Forgive me if this is just a dash vent as that would be a stupid question eh... eh. Also, what is the effect of doing this please? What does it achieve?

It's possible the actuator rod isnt completely opening up, do you get cold air in summer or only cool air?

Good question. In summer with the AC on, it doesn't blow as cold as you think it should. The car was fairly recently imported last summer so I'll assume the AC was de-gased / re-gased and therefore this part of the AC function is OK. Perhaps this points to your diagnosis......Fan only cold is hard to judge as everything is too hot in summer and too cold in winter, when set to 18 degrees.

So, let's say it's the actuators, how do you fix these? Where are they? More to the point, to what kind of person do I take it to for fixing as I'm not the type (unfortunately) to get my hands dirty.

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

paper trick?

OK, I stumbled across FH last week but couldn't do anything with it. When you say 'outside vent' what do you mean? Where is this located and how do I close it. Forgive me if this is just a dash vent as that would be a stupid question eh... eh. Also, what is the effect of doing this please? What does it achieve?

sorry my bad i meant turn it to recycle air not bring it in from outside

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

mine has this problem but if i put my finger on the electrical plug at the bottom of the unit and push up the unit works while my finger is stiil pushing

I do the exact same thing, in summer i push that plug up to do to full cold, in winter i do the same to get it to full hot position. Ive got long enough arms to be able to do it while driving, though i prefer doing it at lights

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
    • It sounds like you want what the Toyota Landcruisers have for their roof racks. Wanna know what you end up with? Rust holes in the roof, and water everywhere...
    • Discovered today that if I select reverse first and take my foot off the brake, then select drive, the drive indicator light works and so does the tiptronic gear indicator. 
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Does anyone here have any ideas?   Cheers guys
×
×
  • Create New...