Jump to content
SAU Community

Recommended Posts

Yawn. So much prefer to be asking tech questions to get more power or handling....but anyway. My daily GTR's heater doesn't run hot enough. Cold Melbourne mornings over-run it. Says 32 on the dash display but I'd think the heat is equivalent to 24 at best.

In all other respects the heating cooling ventilation is working as you'd want.

Any ideas on a fix other than replace the 'head unit'?

Link to comment
https://www.sau.com.au/forums/topic/324009-r32-gtr-cabin-heater/
Share on other sites

not sure if it's the same system as the early 180sx's (mine was 1989 same era as the R32's) but there was a way to get into the diagnostics for the climate control and you can set a bias for the temperature sensor.

the idea would be to make it think it's only 16C when it is actually 20C and therefore it will try to heat more (for example).

somewhere on this forum should be a post on how to get into the diagnostics. also make sure that the temp sensor in the cabin is plugged in and mounted correctly. there should be some small slits somewhere around all the other controls on the dash, thats the intake for the sensor. it should have 1 plug and 1 small (wide as a thumb) tube coming off it.

hopefully that helps.

close outside vent then turn all way up once it is all the way up push and hold the hot button till "FH" comes on, the same can be done for cooling with "FC" appearing on sceen

OK, I stumbled across FH last week but couldn't do anything with it. When you say 'outside vent' what do you mean? Where is this located and how do I close it. Forgive me if this is just a dash vent as that would be a stupid question eh... eh. Also, what is the effect of doing this please? What does it achieve?

It's possible the actuator rod isnt completely opening up, do you get cold air in summer or only cool air?

Good question. In summer with the AC on, it doesn't blow as cold as you think it should. The car was fairly recently imported last summer so I'll assume the AC was de-gased / re-gased and therefore this part of the AC function is OK. Perhaps this points to your diagnosis......Fan only cold is hard to judge as everything is too hot in summer and too cold in winter, when set to 18 degrees.

So, let's say it's the actuators, how do you fix these? Where are they? More to the point, to what kind of person do I take it to for fixing as I'm not the type (unfortunately) to get my hands dirty.

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

paper trick?

OK, I stumbled across FH last week but couldn't do anything with it. When you say 'outside vent' what do you mean? Where is this located and how do I close it. Forgive me if this is just a dash vent as that would be a stupid question eh... eh. Also, what is the effect of doing this please? What does it achieve?

sorry my bad i meant turn it to recycle air not bring it in from outside

Since you get cool air in summer, and warm air in winter, I think the servo arm (i call it the actuator rod) is stuck in-between, neither cold or hot. Try the paper trick and see if you can hear the servo motor moving the rod to full hot or full cold position.

mine has this problem but if i put my finger on the electrical plug at the bottom of the unit and push up the unit works while my finger is stiil pushing

I do the exact same thing, in summer i push that plug up to do to full cold, in winter i do the same to get it to full hot position. Ive got long enough arms to be able to do it while driving, though i prefer doing it at lights

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
    • Not yet quite as bad as what we've seen a Jim Berry clutch do in an R32 GTR though when it decided to cut a chassis rail in half... Still very very gnarly and a great reason to avoid.
×
×
  • Create New...