Jump to content
SAU Community

Recommended Posts

OK so here's my issue...

car's been running pretty bad (especially off boost).. spluttering and not having much power.. also the fuel pump has been noisy, the windows have been slow to move up and down, when idling and i turn on the headlights the revs drop, and the stereo has been making a buzzing noise that changes pitch with the revs..

last time i had that noise it was my old altinator dying.. this time i changed the altinator, but it had no effect.

So i went on to change the battery and hooray! the car worked perfectly for a day or so, but now had started slowly developing the same issues as before.

Now i'm thinking it's bad wiring, but how do i work out where the problem is...?

would i see an improvement if i ran a 2nd earth cable from the battery to the chassis?

Link to comment
https://www.sau.com.au/forums/topic/324339-electrical-issue/
Share on other sites

It couldn't hurt. Maybe check all connections to make sure they are clean and nothing has come off somewhere. Other than that get an auto electrician to have a look at it and they should be able to tell you where the problem is.

I have an earthing kit on mine (came like that from Japan) and it is supposed to help. You could try installing one of those, there is a guy in Perth, Volatile Customs or Audio something or other that makes a kit up (he may install them also).

Volatile Car Audio

Good luck.

Edited by jonn

start with the battery terminals/lugs, the standard ones are pretty shitty and can be pretty lose even when fully tightened.

and before you run new cables check all the earth points and main connections like on your started and alternator, even scratch the paint off where the earth points are. do all this before u do cable upgrades. no point running a new cable to a shitty earth point.

is the alternator new or a recon? just because its been done recently doesnt mean it cant fail.

but going from wat you've said about the new battery fixing the prob for only a day, id start with the terminals

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
    • I have too much trauma from every skyline I've ever seen having crushed jack points/pinch welds lol.    Yep, works 100%, it's what I use when I'm using the quick jack. Don't know why I can't also bring myself to do the same thing when I'm using a jack. I blame the skyline PTSD. 
×
×
  • Create New...