Jump to content
SAU Community

Recommended Posts

hey, i have an ECR33 that will only ever be used as a daily drive.

I have some TE37s on there at the moment 18*8.5 front and 18*9.5 rear.

I need to eliminate the camber im getting, but im not sure on what products are a good buy or waste of money.

Some guidance would be greatly appreciated.

cheers.

Link to comment
https://www.sau.com.au/forums/topic/325129-what-camber-kit/
Share on other sites

Check what's for sale by forum sponsors, if no luck there, try Option1Garage.com.au

The adjustable arms you'll find there are good but are made to a price point. The next jump up from there is Cusco (or similar Jap brand) which you'll pay about $450-$600/pair for. Not many people spend the extra money for the jap stuff, that I know of, I know plenty of people running the option1garage arms with success.

Link to comment
https://www.sau.com.au/forums/topic/325129-what-camber-kit/#findComment-5296515
Share on other sites

i've been reccomended super pro bushes by my mechanic and he's a pretty well respected skyline mech in Adelaide.

but any ones which are poly urethane are good, such as whiteline.

i am going super pro because they're the same material but they are just a little cheaper.

i have a r32 GTR with whiteline sway bar on rear and tien super street coilovers, and i am going to do:

adj castor bushes set to max

adj front upper camber bushes to give a little more camber

adj rear upper camber bushes to remove a little camber

also i don't track my car, it is just a street car which i use for a little bit of spirited driving, it doesnt see any extreme driving like track days.

Link to comment
https://www.sau.com.au/forums/topic/325129-what-camber-kit/#findComment-5303462
Share on other sites

i've got the performance-guru (off ebay from NZ) adjustable rear upper camber arms. excellent price. i cant fault them. they have rubber dust boots on the spherical joint. they seem to be pretty good quality. even the steering/suspension specialtist who adjusted them was impressed with them.

a918_1.JPG

Link to comment
https://www.sau.com.au/forums/topic/325129-what-camber-kit/#findComment-5303542
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...