Jump to content
SAU Community

Neo Motor Cuts Injectors At 2500rmp In Neutral

fubar

By fubar,
in Engines & Forced Induction

 Share

Recommended Posts

fubar Enthusiast

fubar

Posted
Posted

Heya peeps

Just replaced my blown neo motor in my r32 in installed a second hand long motor in. Now if you stab the throttle it will rev high then cut but if you slowly rev it to 2500rpm it cuts the injectors. i tested the hz to the injector and it dropps of completly at 2500rpm.

There is a few mods to the car so one of these could be the problem but was just wondering if any1 has come across this before and has a quick fix, that would be sic:)

Cheers

Dan

fubar Enthusiast

fubar

Posted
  • Author
Posted
doesn't limp mode kick in around 2500rpm? that's often caused by a dodgy air flow meter.

Yeah that sounds about right but i can stab the gas and it will rev high. How do you test the air flow meter, change it? Its a z32.

The motor had standard intake manifold and injectors, i have now put a front intake plemun, 650cc injectors, fuel rale and regulator and 80mm throttle, so she is over fueling big time atm.

Im just trying to get it driveable to get it to the tuner then the nis tune will go in.

fubar Enthusiast

fubar

Posted
  • Author
Posted

yeah stock ecu (its an rb20det ecu and loom) but it has some kinda chip on it from japan! and it is running a dodgie safc 1 the old school one with the dials lol

I think it is just running so rich it is going into limp mode. I've dropped the fuel pressure to 2 bar and leaned out the safc but still no luck. I wanted to give it a good run just to make sure everythin is ok like water lines etc before it goes to the tuner

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Quieter performance exhausts (or muffler add-on options)

      By Murray_Calavera · Posted

      Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • f00stx
      Quieter performance exhausts (or muffler add-on options)

      By f00stx · Posted

      So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
×
×
  • Create New...