Jump to content
SAU Community

Recommended Posts

Hello all

just needing an opinion about the fan on my R33 its roaring all the time especially when you acclerate is this normal?

its been doing this the last few days it drowns out the engine noise as soon as I drive off to work early in the morning the fans roaring

and when I'm on my way home from work its roaring as well in all the 4 years that iv'e owned this car i've never heard the fan this loud

and the temp guage is sitting on just a bit above cold, when i got it serviced early this month I asked the guy to checkout the thermostat

and they told me straight away that there is nothing wrong with it, what do you guys think.

Link to comment
https://www.sau.com.au/forums/topic/326621-r33-is-fan-running-ok/
Share on other sites

well the temp gauge should sit about halfway when running, so there is something going on there. this however shouldn't be causing the fan to be roaring. i would still look at changing it.

as for the fan, the clutch in the fan is probably stuffed and therefore it isn't disengaging. this is better than having it not engage at all because it at least means the engine can't overheat. simplest sollution is to find someone selling a clutch fan and try putting that in to see what it does.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
    • It's TWO steering wheels actually. 😛 one for each hand They are wheels, and they steer!
×
×
  • Create New...