Jump to content
SAU Community

Recommended Posts

Hi all, havin problems with my aerial since I went to put my tv in car, that wouldn't work, so I put the other cd player back in and now the aerial won't go up and down even though it's hooked, and the clock is dull like it's going flat. Any help would be great.

Link to comment
https://www.sau.com.au/forums/topic/328042-r33-aerial-and-clock/
Share on other sites

sounds like u have blown a fuse. dont worry its easy to fix. u know the fuse compartment on the drivers side in the car? look in there and i think its a acc fuse i could be wrong just check them all and replace. i had similar thing happen to me so i checked each fuse (stupid Japanese righting :laugh: )

the reason. because u were drawing over the 20A that the fuse is made to brake at when u put the TV in the car

Well i tried all the fuses, none blown, not sure what else, clock doesnt have any power now, dead. i will pull off the surround again and look to make sure everything is right behind there, but im 100% sure it is. Any other clues.

i dont know what else it could be... maybe a angry wire that is earthing out? but then the fuse would have blown.

hmmm maybe get the audio wire diagram for your car and for ur head unit and check that everything is were it should be

low voltage on the line for the power antenna or bad ground on antenna and or radio.

clock dim ??? lcd or fluro type clock lights?

I would guess low voltage on that circuit, if the fuse was blown it wouldnt work at all

clock LED only needs a few volts, power antenna needs 12v

Well after searching this site, there has been alot of people with the issue over the years asking about it, but i have not read how they fixed it, did they simply give up and rewire the clock, and in my case my aerial wont go up and down. I have checked everything that i can think of or see and its got me stuffed. Usually im actually quite good at finding issues like this, but not this one. Oh well keep searching for a answer. Thanks to anyone who knows how to solve it.

check the voltage output to the antenna? 12v ?

clock can fail, old nissan clocks did all the time ?

got a photo of it to see ?

antenna ,does it even make motor noise when the radio comes on? if so it's got a broken plastic winder thing inside and most can be fixed

some aftermarket/oem ones use a relay to boost current to put the antenna up? have you investigated that?

I did look around at relay but couldn't see one that it would come under, going to pull aerial connections of this afternoon as I finish at 1 on Fridays so I will actually have some daylight. If I can figure it out, I will just rewire the aerial with it's own online fuse, same with clock if I have too. It's just odd cause the constant power wire for the head deck is only pushin just over 2v all the time, I have to run my own just to get it to work. But thanks to everyone that's tried to help so far.

Well everything is working again, I lost my indicators last night, checked all the fuses and nothing blown, but they still flashed with the alarm, so I checked fuses avian and found one dead, put that back in and clock and aerial started working, but still no indicators, then I fiddled putting the fuse in all the way it can and just tested once more and there they were. I must have a loose connection behind the fuse box, cause I triple checked all the fuses the other day and none were blown. The whole fuse box inside the panel moves so it would not suprise me. So sorry I don't have a solution for anyone else who has this problem, all I can say is check third fuse up from the bottom, left side in side the car, that's the one that ended up shitting itself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...