Jump to content
SAU Community

Recommended Posts

Hey ,

Got my car from Japan today - Driving it home, realised that the rear suspension squeaks to buggery !! It's really annoying as it only happens when you are going really slowly with little to no engine noise. Its like the rear shocks go down like 1-2mm and it make this god awful noise.

The car has after market coils and shocks - don't know what brand yet as I haven't had time to pull the back wheels off. All four corners are damn stiff though.

Put it this way, you open the boot and push down on the rear and you can hear this noise squeak thu the chassis.

It sounds like the shocks need a bit of an oil - But I thought this was all internal ??

The car handles well and can take a fairly decent pothole without jarring too much.

Can anyone gimme some advice on what to look for or what to do with this problem ??

Many Thanks,

Link to comment
https://www.sau.com.au/forums/topic/3281-sqeaky-rear-suspension/
Share on other sites

Ripped wheels off tonight -

The shocks are Tanabe? (never heard of them??) - Looks like the rubber boot that is meant to go over the main shaft of the shock has perished. Don't know if the shocks are any good or not - So I WD40'd the lot - The noise is better, but still there.

I might take it down to Pedders or another suspension shop = see what they reckon.

Recomendations for suspension shops in Sydney ???

Cheers/

yeah i was goin to say that but i didnt know how to explain it the springs sometimes squels where it sits in the shoe of the shock usually cause aftermarket stuff is metal on metal wheras factory have a little rubber boot on the ends of the springs id say a generous amount of electrical tape would do the same thing wrapped around the end of the spring crap job though pulling all the springs out for squeekes!!:D

tanabe usually supply things to nissan like radiators and hoses n ***** are they anything special like hieght adjust. or shocker adjustable if not i didnt know they made shocks!!! Just be carefull with places like pedders cause they try n tell you all this stuff that there "diagnostic machine told them" about you need this that and the other replacing so they can make some money off you

No, not adjustable or anything (Damn Hard though) - The shock part of it is Orange and I they are called Viper Street somethings - Looks like you can undo the top of the strut tower and remove the shock cartridge (As you can tell I have no idea what all this stuff is called) Anyway , it didn't look to difficult to get at so I might pull them apart, clean everything , make sure all the rubbers are OK, test the shocks. Dunno what to do if the shocks need replacing as there would be no Tanabe spares in Aust hey ? Maybe someone else make a shock that is the same ??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...