Jump to content
SAU Community

Recommended Posts

now that you told the world what to expect in your car !!!! , the crims can plan the disable of your GPS ...geez

when will people learn do not discuss what is in your car , alarms wise on forums !!!! not too wise

yes even gps can be foiled in a big hurry if you know its in the car.

I rigged up a hydrogen bomb to mine. Lets see the f**kers disable that.

-D

I think now is another time to get a free plug ...

SAU-SA club members get 10% discount at places like Autobarn Mile End, Ministry of Bass, Auto Perfection etc etc (hope I didn't miss anyone) and these guys stock and fit alarms!

Even if you don't want to join the club ... get an alarm anyway at the abovementioned installers.

And sorry to hear about your loss ... hope it turns up in some salvagable condition.

so many assumptions about security especially from admin and moderators, would expect the members to be that way and the moderators and admin to be helpful, yet its the opposite...the irony. Thanks to the person that pm'ed and those that posted helpful advice. I will be scanning, seaching and following up till my last breath.

Edited by chrish_12at

Hang on - you joined up on SAU to whinge about your stolen car ffs. NOT to be a part of the community, not to help anyone else out, not to be part of anything .... except ask people's help and expect them not to be critical of a car that is uninsured and presumably unalarmed, presumably left out the front of someone else's house - then stolen.

Excuse us for pushing the point that if you don't have an alarm you deserve to have your car stolen, and by not having an alarm you personally cause all of our premiums to go up at next renewal "x"%, due to the additional ABS stat that shows Skylines do, if fact, get stolen.

Clearly if you did have an alarm, kill switches, and a Club lock, but THEN had your car stolen, you would have cleared that point up with us. So we assume otherwise.

If you did have all those things, then my heart truly goes out to you .... we all know that cars still can get stolen despite the best security - which is why even with all my security measures if I HAD to leave my Skyline somewhere unfamiliar I would park another car behind it, or at least pull the fuel pump fuse so they couldn't start the thing. And yes, I really would. When I had my old R34, which did have all the forementioned security items, when I parked at pubs to go play NPL Poker, EVERY TIME I parked at one of the pubs I popped the bonnet and removed my fuel pump fuse. I even purposely blew the same colour fuse and replaced the real one with a dummy - so even if they towed it a short distance and couldn't get it started it looked like the fuel pump fuse was still in there and good.

So clear it up right now, did it have an alarm? Kill switch? Club lock? Was it parked in a garage or on the street?

Have you heard me winge?.... I believe I asked for help. The only thing I have to winge about is your comments. Why should I tell you what security it had, so you can substatiate your assumptions and blunt comments..?. But your right, ive been building cars for 12 years and im stupid enough to have no alarm, no clublock, no anything???... yeah right. Clearly you dont want more people to join your community because with people like you cutting others down like you are, why would anyone want to? What difference does it make as to what terms somebody joins, it shouldn't.....

Im sorry you now need to pay $5.00 more on your insurance, but frankly it gives me a mild amount of satisfaction that im costing you money.

Your extremely rude, reply with whatever you want to justify your comments but Ive got nothing left to say to you. :down:

Hang on - you joined up on SAU to whinge about your stolen car ffs. NOT to be a part of the community, not to help anyone else out, not to be part of anything .... except ask people's help and expect them not to be critical of a car that is uninsured and presumably unalarmed, presumably left out the front of someone else's house - then stolen.

Excuse us for pushing the point that if you don't have an alarm you deserve to have your car stolen, and by not having an alarm you personally cause all of our premiums to go up at next renewal "x"%, due to the additional ABS stat that shows Skylines do, if fact, get stolen.

Clearly if you did have an alarm, kill switches, and a Club lock, but THEN had your car stolen, you would have cleared that point up with us. So we assume otherwise.

If you did have all those things, then my heart truly goes out to you .... we all know that cars still can get stolen despite the best security - which is why even with all my security measures if I HAD to leave my Skyline somewhere unfamiliar I would park another car behind it, or at least pull the fuel pump fuse so they couldn't start the thing. And yes, I really would. When I had my old R34, which did have all the forementioned security items, when I parked at pubs to go play NPL Poker, EVERY TIME I parked at one of the pubs I popped the bonnet and removed my fuel pump fuse. I even purposely blew the same colour fuse and replaced the real one with a dummy - so even if they towed it a short distance and couldn't get it started it looked like the fuel pump fuse was still in there and good.

So clear it up right now, did it have an alarm? Kill switch? Club lock? Was it parked in a garage or on the street?

Stuff the steering wheel, If I get the car back ill give the person that leads to or finds the car 25% of the sale cost. Any percentage of somthing is better than 100% of nothing :down:

Shotgun your steering wheel - if you receive the car back in anything less than 1 piece and want to part it out.

I should rephrase that, i dont think anyone wants the sales cost...sale value :down:

Stuff the steering wheel, If I get the car back ill give the person that leads to or finds the car 25% of the sale cost. Any percentage of somthing is better than 100% of nothing :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...