Jump to content
SAU Community

Recommended Posts

Starting a new thread-the old one was getting a bit skattered

I need $ to buy gear for work so these are up for grabs

Can deliver anything within 150 K's from the Sunshine Coast QLD for extra fuel mone

Or send your postcode & suburb for an accurate courier qoute

Pickups from Maroochydore

All rims are 5 stud/114.3 PCD

-3" mild steel custom straight through catback exhaust with twin tips

No mid muffler-increases power heaps & sounds evil

Fits r33 gts/gtst perfectly & r33 4 doors too

Will also fit s14's if shortened by about 25cm

No damage at all-custom made-welds are allgood

The twin tips sit at a nice angle in the space on stock gtst rearbar

It's on my r33 atm-can deliver it

$280 ono

-MOMO "corse" 320mm all black leather steering wheel VGC

Has two lines of red stitching on the inside

A few small scuffs/marks but in good condition & not faded-horn,etc included

35cm in diametre-centre of mounting holes are 70mm across & 35mm apart

$160 ono

-ONE new gold Driftek rim 17x9 +30 PCD 114.3 [5 stud only-not multistud]

Has had tyre fitted & removed shortly after

No scratches/scuffs/gutter rash at all

$250 ono

-2xWORK "Equip" 16x8 +40 two piece alloy rims with skid tyres VGC

Very lightweight-perfect offset for r33 GTSt Skylines

$150

-4xVGC stock 16" s15 silver rims/2 tyres 60%/2 tyres 85%

$450 ono

-2xStock r32 gtst 16x7 rims in VGC

tyres are just above tread makers but are camber worn a bit

$100 ono

-4xStock r33/s14 silver 16x6.5 wheels GC [have two sets]

with 4 225/50/16 tyres-all 70%

$250 ono

-3xRandom 16x7 +40 alloy rims in good condition-good solid skid rims-look ok

$80

-Stock r33 suspension with stock springs-complete set

$150 ono

-Stock VGC series 1 r33 spoiler-original burgandy paint

light works-light wiring is allgood

$80 ono

-RB25 stock 2.5" dump/frontpipe/cat converter [two of each-frontpipe should fit RB20's too]

$120 ono for all-will sell parts seperately

-r33 gtst HICAS module-no damage

$60 ono

post-59075-1280188081_thumb.jpg post-59075-1280189255_thumb.jpg

post-59075-1280189334_thumb.jpg post-59075-1280189387_thumb.jpg post-59075-1280189462_thumb.jpg

post-59075-1280189546_thumb.jpg post-59075-1280189655_thumb.jpg

post-59075-1280189692_thumb.jpg post-59075-1280189742_thumb.jpg

post-59075-1280189760_thumb.jpg post-59075-1280190034_thumb.jpg

post-59075-1280190138_thumb.jpg post-59075-1280190347_thumb.jpg

post-59075-1280190387_thumb.jpg post-59075-1280190432_thumb.jpg post-59075-1280190456_thumb.jpg

post-59075-1280190486_thumb.jpg

post-59075-1280191542_thumb.jpg post-59075-1280191613_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/330479-jdm-garage-sale-sunshine-coast-qld/
Share on other sites

have 6 stock r32 wheels altogther

two have been professionly resprayed metallic silver

can include four federal 595 205/50/16 tryes all about 50 percent tread but camber worn abit

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...