Jump to content
SAU Community

Rb26 Engine Package 380awkw

HKS26T
 Share

Recommended Posts

HKS26T Experienced

HKS26T

Posted
Posted (edited)

Hi Guys,

Looks like i will probably end up parting this car out. My package list is the following

Trust 264deg easy street cams

Trust springs and cam gears

Trust Metal Head Gasket

Arias Pistons and Eagle rods

Nismo bearings, Oil Pump and Water Pump

Head fully recon'd and lifters set for the cams

Fully balanced

Block and crank crack tested

Block acid dipped, decked etc

Crank linished

Twin Turbo Trust T517z

Trust Hard piping Kit

Trust Intercooler

Trust Intake plenum

Trust Greddy radiator

HKS Fuel Rail Kit

HKS 1000cc Injectors

Tomei Sump Baffles

Haltech E11 v2 current tuned on E85 383awkw @ 22 PSI (25/06/10 @JEM)

Motor has seen about 100 laps at Eastern Creek

Not keen on seperating anything as motor is still in car running

4161810131_6311d634a7_b.jpg

Edited by HKS26T
Link to comment
https://www.sau.com.au/forums/topic/330548-rb26-engine-package-380awkw/
Share on other sites
  • 11 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I am well aware as I did rant at him to buy a MX5, buy the 2.5 before he DIY'ed it, etc as well as do things to the holden. He will obtain a ND. It's the best of both worlds. They look great in person, definitely the best looking one. Just a matter of time now.
    • r32-25t
      NC MX5

      By r32-25t · Posted

      Remember this is the same person who said he’d never own an nc 
    • zique
      Ceramic turbine damage to engine - what did yours do?

      By zique · Posted

      ouch! how is the car now?I had sold my gtr but have been looking into some on trademe and a 260RS but I wouldnt be keen on any repairs needed on them
    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
×
×
  • Create New...