Jump to content
SAU Community

Recommended Posts

I just changed my timing belt, idler and tensioner pulleys. It runs fine, and sounds fine at idle, but over about 4, 4.5k RPM there's a significant humming noise and vibration.

What could it be? Is it normal for a belt to make that noise when it's new? It's just a normal nissan belt. The only other thing I can think of is the tension being wrong, but we spent a while doing it, and my mechanic mate reckoned it was alright.

Suggestions?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/331890-vibrationhum-after-timing-belt/
Share on other sites

We chipped a bit off one of the ridges while taking it out. It's only the light stuff, it probably weighs 20 grams, which we didn't think would make a difference to the balance of something that weighs many times more. Also thought if it was that it would be noticeable when revving it stationary.

Could that be it?

Ouch, could be anything really...when you change a part like this it often brings out different sounds from the moving parts it interacts with because you're resetting positions that have evolved with each other over time. Could be a loose bolt, bad pulley (water pump replaced too?)...

The harmonics of a straight 6 gets worse as the revs climb, I would imagine revving while stationary wouldn't be putting the load onto the crank you would normally get while driving. If I damaged my harmonic balancer in any way, personally I would have binned it and replaced it with a aftermarket balancer. The worse thing that can happen is the oil pump gear breaking in some way.

Think I found what it is. The had a look at the fan, and there seems to be a fair amount of play in it. You can visibly see it vibrating when it's running, so it's probably that. I'll take it off and run it again to see if it goes away when I get a chance.

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...