Jump to content
SAU Community

Gtr Parts. New And Second Hand.

Piggaz
 Share

Recommended Posts

Piggaz Grand Master

Piggaz

Posted
Posted

Hey guys. Its time to get rid of some stuff out of the garage. All items are located in Georges Hall, Sydney (Near Bankstown) apart from the N1 block which is at Beverly Hills, Sydney. Buyer pays postage. Pickup is preffered.

Nismo fuel pressure regulator. Like new. Was on my car for about 10,000 kms. I only changed it because I went to a duel entry fuel rail and a sard reg. $110

N1 (24U) Block. I was going to use this for a build but I bought my car with a GT block in it. I will never use it. $1990

Greddy water pump pully. Aluminium, pretty blue and very light. I bought the set so I have used the alt and PS pulleys but I am using the big ATi harmonic balancer which needs a smaller pulley $50

Standard second hand RB26 coils. Done about 80,000 kms $40

Rays blue valves and valve caps. I got these when I bought my TE37’s. I don’t like the blue, would rather the black. Never been used. $40

Heat wrap. 4 rolls at 1 inch by what looks like 15 metres. It could be 25metres but its all sealed in its plastic and i dont want to unroll it to measure it. These came with the Tomei Expreme manifolds. $70

OS Giken 5th gear. Brand new. When I rebuilt my box I bought the 5 speed but I decided to stick with the standard ratio. $290

Standard OEM 5 speed centre plate. Came out of a box that was 11,000 kms old. $20

Second hand Tomei manifolds. There are a few cracks in them. Might be worth getting them fixed up and throw them on. Done 15,000 kms. $50

Goodridge braided brake lines. ADR Approved. FRONTS ONLY! Bought these thinking they would replace the factory metal line. I went 345mm rotors up the front and it was easier just to get a line that went the whole way. Never been used. $100

Copper radiator. Its roughly 45mm thick. Works very well. On the track with 370 rwkw water temps got to about 85. Barely moved. Has a very small leak where the drain plug is. Easily fixed. $100

Link to comment
https://www.sau.com.au/forums/topic/332222-gtr-parts-new-and-second-hand/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
    • Dose Pipe Sutututu
      Forced Performance Hta Turbos

      By Dose Pipe Sutututu · Posted

      Well, I had an Edward Lee's special edition odo windback car/motor with a RB25DET S2 and I put down 372kW with a good amount of track abuse for 1.5 years before the ring lands decided it didn't want to stick around anymore 🥲 But probably didn't help I kept on smashing try limiter on the track and a few skid pans.
×
×
  • Create New...