Jump to content
SAU Community

Eoi: 89' Hcr32 Gtst S2rb25det W/bhg

krayzie32
 Share

Recommended Posts

krayzie32 Mentor

krayzie32

Posted
Posted (edited)

$7500 Firm As Is

$12500 Repaired by Dahtone Racing w 12months Rego & Fresh Tune

'89 HCR32 Type M Black Sunroof Model

Type M front Bar, Skirts,

Rego til 09 Sept 10

S2 RB25DET w/BHG

45mm Dual Core Alloy Rad

Cooling Pro 600x300x70 FMIC Kit

Walbro 255Lph 550hp Intank pump + fuel relay bypass

Garrett TB34H Turbo A/R0.50 Comp A/R.58 Rear + Custom V Band Dump Pipe

Hollow Cat + 3" 5Zigen Pro Racer Spec A titanium Cat back exhaust

Complete S2 Wiring Loom/ECU/Ancillaries/Z32 AFM/HKS F Con SZ + Loom + Greddy Profec B Spec II

NISMO Coppermax Clutch Kit W/NISMO Lightweight Flywheel 2000kms OLD

Hardie Spicer Custom Balanced Tailshaft to suit RB25DET Box

07/97 S2 RB25DET 5Spd Box W/Mechanical Speedo Mod

Hicas Lock Bar + Complete Hicas Removal + RB25DET Power Steering Pump

Weds White Mesh 17x9+30 All round

GAB Adjustable Dampening Front suspension (Lower & Stiffer than Std)

KYB Rear Suspension (Lower & Stiffer Than Std)

RG Adjustable Castor Rods

Nismo Front Strut Brace

No bubbles in dash

no tears in seats

no missing vents

requires a little tlc on body, light scratches (rust developing in sunroof & boot near rubber surround)

Note does not come with R32 GTR Bonnet/Front Bar/Rear Spoiler/N1 Lip

f375fa5b.jpg86a16e25.jpg

Has cost me a F**k load and a year long head f****ng

Long story short blew rb20det head gasket on a trackday

so went all out and done rb25 conversion, imported built motor from japan and ended up putting 3bar through it duE to leaking vacuum line and wastegate didnt open (happened on dyno) dropped cylinder 1 & 3 and damaged near new HKSGT2535 Kit along with it

bought long block bolted everything to it, and sold most of upgraded parts to cover some costs

only to have recieved yet another bhg whilst tuning was done

i can afford to repair but i dont want to keep the car as another opportunity has arisen...

So i dont see the need to repair only to sell later

Am contemating repairing, also contemplating another longblock, also contemplating a complete return to RB20DET & box & loom and all associated.

Edited by krayzie32
Link to comment
https://www.sau.com.au/forums/topic/332450-eoi-89-hcr32-gtst-s2rb25det-wbhg/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...