Jump to content
SAU Community

Enkei Wheels

Adelaideprosound

By Adelaideprosound,
in South Australia

 Share

Recommended Posts

Adelaideprosound Proficient

Adelaideprosound

Posted
  • Author
Posted (edited)

Iif i were you i would do a good check on thos willwoods because in my experience they taper the pads due to not having correct piston sizing in the caliper. They are probably improved by now though i dunno.

And if you think the Enkeis are expensive i just spent $3900 on a set of Volk CE28N for my GTR. :P.

Edited by Adelaideprosound
Link to comment
https://www.sau.com.au/forums/topic/332545-enkei-wheels/#findComment-5397918
Share on other sites
Dohmar Grand Master

Dohmar

Posted
Posted
I got those on my Supra.

think these look dope

rpf1_black_edition.jpg

quick question - 18" x 9.5" with +15 offset, that should fill the guards on a 32 gtr without needing to use spacers or roll guards yeah?

when it comes to offset and the like im a noob

-D

Link to comment
https://www.sau.com.au/forums/topic/332545-enkei-wheels/#findComment-5397979
Share on other sites
Dohmar Grand Master

Dohmar

Posted
Posted
Thats a perfect size for a 32 GTR. And they will fill them beautifully. There shouldnt be any scraping issues.

sweet

they are some seriously sexy rims. its either them for the price you quoted or 34gtr rims which are always used...

will you be able to throw in centre caps for the prices quoted? I notice some websites dont bundle the two

-D

Link to comment
https://www.sau.com.au/forums/topic/332545-enkei-wheels/#findComment-5398088
Share on other sites
SLED Grand Master

SLED

Posted
Posted
Iif i were you i would do a good check on thos willwoods because in my experience they taper the pads due to not having correct piston sizing in the caliper. They are probably improved by now though i dunno.

And if you think the Enkeis are expensive i just spent $3900 on a set of Volk CE28N for my GTR. :) .

They must be the flavour of the month George cause I just did the same thing for the EVO.

I got those on my Supra.

Ahhh, I spotted your Supra in a certain workshop down south the other day..........was checking your front pulley out.....hope the issue for your sake is the balancer and not the crank key, ouch. :P

I need to speak to you again about our last conversation so I'll give you a ring soon. :huh:

Link to comment
https://www.sau.com.au/forums/topic/332545-enkei-wheels/#findComment-5398276
Share on other sites
Adelaideprosound Proficient

Adelaideprosound

Posted
  • Author
Posted
sweet

they are some seriously sexy rims. its either them for the price you quoted or 34gtr rims which are always used...

will you be able to throw in centre caps for the prices quoted? I notice some websites dont bundle the two

-D

They all come with Enkei centre caps, each wheel has their own sprocket to tighten wheel nuts and they also come with nice chrome valves.

Link to comment
https://www.sau.com.au/forums/topic/332545-enkei-wheels/#findComment-5398540
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...