Jump to content
SAU Community

Recommended Posts

This is a common problem. Almost certainly it's the diode in the circuit under the red plastic. Check the fuse first to make sure, but I think the same fuse controls other things like the rest of the brake lights so you'll probably have no brake lights at all if it's the fuse.

Remove the whole lighting assembly (I think it's held in with 2 screws from underneath) and check the circuit with an ohmmeter. If it's open, then it's probably the diode. Separate the red lens from the backing plastic with a razor blade or the like, and look near where the wires go in, you'll see the diode and probably notice it's burnt out.

You can either replace the diode with the same type, or just put a straight piece of wire in. The diode is only there to stop the whole series of LEDs getting zapped if you wire it in back to front, which you won't do because the plastic clip is directional. So a bit of wire is fine (that's how I fixed mine).

Put it all back together, using spots of super glue here and there to hold it in place. Not too much though because you want to be able to pull it apart again if you need to fix it in future. If you use wire instead of another diode though you probably won't ever have to fix it, except to replace individual burnt out LEDs, which is a total bitch to do and probably not worth the effort.

Hi JimX,

Many thanks for your reply - I was hoping I wouldn't have to pull it apart but it looks like it will need to be - I'm just thinking where the screws are, is ther 2 screws under the spoiler in the middle and the led lens bit will slide out or something?

Yeah that sounds about right. I'd like to give you a definite answer but I fixed mine so long ago that I can't remember. And I'm at work so I can't check for you :D I'm pretty sure it's just 2 screws, one either side and underneath. I used a stumpy philips head screwdriver under there somewhere.

Hi

The thingi that Jimx called a diode is really a resistor and it is there to drop the voltage down so you dont blow the LED's so putting a piece of wire in is not a good idea. mine was burnt out so could not see how many ohms it was. I worked out it should be around either 47 or 470 ohms (I cant remember, its writen down at home) If you can see the colours on it can you please let me know,

Mine has gone too. I've had a couple of cracks at separating the red from the black plastic... Its a BIATCH! :cuss: I'm making progress, but I end up just putting it back in after a while of cutting with a stanley knife. Might have another go this arfo.

BTW: it's 3 screws on an R33 :(

Nah, it's a diode. There's a diode sign on the circuit board and you have groups of 4 or 5 diodes running in series, dropping the voltage to each to somewhere between 2 and 3 volts removing the need for a resistor.

Put a diode in. Not that it means much, since all the LED's are diodes anyway :O Just bridge it if you don't have a replacement diode handy. I had one lying around and it's been working for 12 months.

Hi

The thingi that Jimx called a diode is really a resistor and it is there to drop the voltage down so you dont blow the LED's so putting a piece of wire in is not a good idea. mine was burnt out so could not see how many ohms it was. I worked out it should be around either 47 or 470 ohms (I cant remember, its writen down at home) If you can see the colours on it can you please let me know,

Serlock_nz

Its a freaking diode man. I was the electrical knowledge guy that helped jimx fix his spoiler light. From a rough memory the diodes are grouped together that the forward voltage drop on them is enough so you dont need to worry about dropping the voltage.

Lets just say that jimx's haev been running fine for at least 12 months and leds blow pretty fast when you put 12v or higher through them.

Cheers

Bombster

Well the one that I replaced was a resistor because I could see a couple of coloured rings but couldnt tell what colour the other rings were,

In mine only one section of the LED's had gone out, about a dozen.

they must use both diodes and resistors on the different models

Would I be right in saying to identify which you have, diodes are usually black with a silver ring around them with the diode symbol, and the resistor is usually cream coloured with coloured rings around them to show resistance value

Cheers

Well hmm. It doesnt matter if it is a diode or a resistor. Both diodes and resistors lower the voltage.

The average diode will drop the voltage around 1.5v and have the added bonus of only conducting in one direction for polarity protection of the circuit.

If you replace either with a piece of wire you may not necessarily destroy the device immediatly but you may reduce the potential lifetime of the LED's in the brake light assembly. Depending on the tolerence of the circuit of course.

Chances are nothing bad will happen.

  • 1 month later...

I have the same problem :)

I took the unit out from under the spoiler, but I have absolutely no idea how to get it apart to fix the diode! The unit seems impregnable!

Has anyone got any tips, instructions or pics on how to get it apart?

Thanks.

I think the whole light is around $200 second hand. Once I used the razor blade, I kind of levered it apart with a screwdriver. I managed to chip a small bit off the red part, so be careful.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...