Jump to content
SAU Community

Recommended Posts

s13/180sx sideskirts, unsure of brand, fibreglass, pretty much brand new, ran it on a car for 50 km then the owner didnt like it and took it off

$150 OR MAKE AN OFFER WANT EM GONE

dsc04539j.th.jpg

front bar and rear bar for s13, front bar is off a two tone (blue and silver) k's silvia has the vent for the side mount intercooler, both come with the foam bit and both are in good condition jst faded paint, the rear bar is in very good nick also the rear bar will come with the number plate light, can separate for less money

$100 bucks each or nearest offer

dsc04556z.th.jpg

s13/180sx mud guards all in good nick, black in colour

$50 for all 4

dsc04544o.th.jpg

180sx sr20 front bar lip $120 ono for the lip

100 for the bar (has parking antenna, very rare)

dsc04561hq.th.jpg

s14a (series 2) front bar, painted satin black, in good condition has 2 cracks but lines up perfectly DOES NOT COME WITH LIP as i am using it, comes with indicators

$120

dsc04562qy.th.jpg

s14 sideskirts, fibreglass, unsure of brand but those who are after the subtle look should buy these, no cracks, in good nick

$150 ono

dsc04564c.th.jpg

s14a door trims, in excellent condition, little imperfections but cant notice em, comes with vent

$250 for the pair or make an offer

dsc04565x.th.jpg

s14 rear strut brace, very thick and cool design

$150 or nearest offer

dsc04566w.th.jpg

180sx B WAVE WING, real rare shit, ummm in very good condition and looks gangster if your going for the old school look

$350 OR MAKE AN OFFER, not sure if i wanna keep it or not...

dsc04569y.th.jpg

s14 jdm rear bar, fibreglass, has been repaired comes with number plate light, looks a lot better than the adm rear bar, over all good condition

$150 or nearest offer

dsc04570h.th.jpg

s14 jdm rear pods, fibreglass once again but in very good condition, very subtle and nice on the car

$170 or nearest offer

dsc04571g.th.jpg

s14/s15 4 pot brakes with brand new brake pads, used, could do with a coat of paint otherwise good condition

$300 ono

dsc04574g.th.jpg

saas steering wheel for s13/180sx comes with HKB boss kit also fits r32

$70 for the wheel and bosskit together

dsc04580o.th.jpg

r32 gtr seats, drivers side and passenger side, in immaculate condition, only tiny tear on the drivers side and has been repaired refer to pics

asking $750 for the pair or make an offer

dsc04582zt.th.jpg

dsc04583z.th.jpg

dsc04584v.th.jpg

dsc04585dr.th.jpg

r32 gtr wing, could do with a touch up but otherwise in good nick

$140 or nearest offer

dsc04587p.th.jpg

located in western suburbs melbourne

pm or call 0413 926 794

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...