Jump to content
SAU Community

Recommended Posts

right

once again i have grabbed a half cut, i have kept the engine and box but the rest of the shit is available

so send me a pm and ill see if i have it

other shit

panasport g7's, 17 by 9, suit r32 gtr +20 offset, these are a tough rims and are old school 80/90 cool

tyres are dead, some minoe gutter rash on a few( LIGHT WEIGHT AND AWESOME TRACK RIMS)

$1200

IMG_6884.jpg

panasport 17, 8 front 8.5 rear, i have a sick thing for panasport rims but i ned to move a few to pay for my engine rebuild

these are perfect for a r33 gtst or a s14 silvia,

$1000( LIGHT WEIGHT AND AWESOME TRACK RIMS)

IMG_6883.jpg

enkin p1( i think) 18 X8(235 pricey michelin pilot rubber 60%) and 18X9(265 continental rubber(60%))

$1200

IMG_6876.jpg

IMG_6877.jpg

r32 gtr rims with dud rubber $450 these ones have some gutter rash

IMG_6867.jpg

r32 gtr rims with awesome rubber $700

IMG_6870.jpg

IMG_6870.jpg

Link to comment
https://www.sau.com.au/forums/topic/334616-fatz-shed-clearout/
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Hey oh handsome one.....fix up the pic of the Panasports. Looking for a set, even better if you can throw them on a car with a brake setup and give me an idea of internal wheel clearance. Better/worse then the Weds uncle Dunan hooked you up with etc etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...