Jump to content
SAU Community

100 reasons you should NEVER take your car to JV crash


Recommended Posts

1. They never stick to their promises. Proof: To sway me to get them to fix my car, the ****er said he would fix some other things for free, at no cost to me, this was a front bumper and a few little things. After i gave my car to them he went back on his word and said he would do what i asked. so i just said fine, just fix the rear end properly.

2. They are dodgy. Their work is dodgy. Proof: after the first time they fixed my rear end, the assessor came back to me and said that the whole job needed to be done again. The did some of it again and realigned some of the panels, it looks better now.

3. The ****er lies. Proof: they said that nationwide(who is a company that helps u recover money from the other insurance company) will recover money off the other persons insurance at no cost to me, full stop. JV pays them money so that jv can get the contract to fix the car. the ****er wont' give me back my car unless i paid the fees. Even after we just had an argument which i've totally recorded on my phone and u can clearly hear him admitting that he said that i wouldn't have to pay anything. if you want i will find some way to get it off my phone. so i just wanted my car back so i paid and said that they should expect a letter from my lawyer which i'm getting advice from now.

4. hes just a ****ing ugly ****.

5-100. they just suck.

btw: hes reasoning is that ... he shouldn't have to pay for it cause he couldnt' get the insurance company to pay for the fees. so he said that i should pay for it even though he gave me his word that i wouldn't have to pay for anything.

Yeah their work is pretty shithouse. ON my old car, i had a panel replaced, and the colour wasnt anywhere near the body work. It was like they were drunk when they did the colour matching. Faggots. And to top it off, they put a fat "JV CRASH" sticker on the side of the door, which is impossible to remove. ****wits.

some business's are dodge and should not be trading but, if you are taking it further legally i would seriously consider removing your post. they would have a strong counter sue case of defamationagainst you and that would add insult to injury to you.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...