Jump to content
SAU Community

R33 Crazy Sell Up

NismoGTR33

By NismoGTR33,
in Tasmania

 Share

Recommended Posts

NismoGTR33 Apprentice

NismoGTR33

Posted
Posted (edited)

selling up everything, 1st off wine red 93 gtst 6 months reg and roadworthy, converted from auto to manual

still in the process of adding some bits from my other car and cleaning up engine bay pics are just some quick ones i took today

also still might put the lowered king springs on it and i have a set of 17inch 9inch wide 245-45 front and 9&half wide 255-40 rear SSR integral GT1,s on off the other car

18inch8s and 9s on rear(ATM)

standard suspension New looking shocks

brake pads 90% rotors not warped

trust side skirts and front lip, some kinda custom grill?

new Exeedy heavy duty clutch

rb30, stock completely reco bottom end, twin cam oil pump and oil cooler, stock reco twin cam head 2000kms

New coolant, oil&filter

New synth gear oil

Radiator cleaned out new top tank and twin thermo,s

Greddy style plenum match ported Dag's taken off powder coated

High mount and tial 38mil W-gate & screamer pipe

3 inch to 3&half Straight through exhaust

GCG High flow turbo (Not pictured on car)

R34 GTR Fuel Pump

Z32 Afm

K&N Pod

Nismo oil cap

Apexi BOV

Apexi Super ITC (ignition converter)

Apexi AFC Neo (airflow converter)

Greddy Profec-A (boost controller)

front and rear strut brace

Tidy clean condition inside

Momo R-Evo wheel(not pictured)

Cd mp3 Player, aftermarket speakers installed

Nismo clear side indicators

Led number plate lights

Nismo gear knob

Drift A/F and boost gages on pillar pod(not pictured)

Original skyline floor mats

Front bar indicators Not put on yet

Also have a silver 95 series 1 and half still 2 Months rego left

no motor or gearbox, bonnet or headlights body rough in spots(pics)

rear rotors Machined, New rear pads,

custom 6&half inch door speaker pods(under door trim), fully dynamatted doors

Very neat car inside

Original floor mats

car was running and driving fine

Other random parts

Series2 1997 automatic transmission with MV AUTO Stage3 Shiftkit just pulled out of car for manual conversion

(Perfect working order awesome auto to drive instant gear changes)

2 complete rb25 bottom ends cracked pistons(will hone out if doing the cheap)

1 rb25 stock head

2 inlet plenum's and exhaust manifolds

1 series turbo (very good condition)

1 complete radiator

2 standard clutch fans

3 starter motors

2 flywheels

2 rear rotors

bran new unopened Bendix ULTIMATE Front pads (160$)

2 AFM,s

Big K&N pod

series2 ECU

chopped wiring loom

full turbo back 3inch exhaust system with bellmouth front pipe

near bran new 3 inch stainless cat

heaps more to list various standard bits and pieces

Ide prefer to sell it all in one hit will separate the two cars, I'm not hunting for top dollars if anyone would like to make some offers feel free thanks.

post-76202-1283337031_thumb.jpg

post-76202-1283337104_thumb.jpg

post-76202-1283337112_thumb.jpg

post-76202-1283337119_thumb.jpg

post-76202-1283337168_thumb.jpg

post-76202-1283337180_thumb.jpg

post-76202-1283337195_thumb.jpg

post-76202-1283337210_thumb.jpg

post-76202-1283338411_thumb.jpg

Edited by NismoGTR33
Link to comment
https://www.sau.com.au/forums/topic/335180-r33-crazy-sell-up/
Share on other sites
NismoGTR33 Apprentice

NismoGTR33

Posted
  • Author
Posted
hey mate u wouldnt be willing to sell me the breather setup fromthe rb 25 head would u? i need the two fittings for the cam covers??

um yeah i just need another inlet side fitting for a catch can on the red one but im sure ive got like 3 sets of cam covers, and some fittings are a tad smaller and fit loose ill have a poke around later today see what i can find. so you want one of each of the two?

andygr32 Rising Star

andygr32

Posted
Posted
um yeah i just need another inlet side fitting for a catch can on the red one but im sure ive got like 3 sets of cam covers, and some fittings are a tad smaller and fit loose ill have a poke around later today see what i can find. so you want one of each of the two?

its allg ood man i got a fitting from autobarn today! all i neeed is the pcv valve now...im trouble shoooting an oil blowing problem..

NismoGTR33 Apprentice

NismoGTR33

Posted
  • Author
Posted
its allg ood man i got a fitting from autobarn today! all i neeed is the pcv valve now...im trouble shoooting an oil blowing problem..

Well if ya get stuck for a PVC got a few kickin round, i just took my whole crankcase recirculation setup off, pvc etc, on boost was ok but as soon as i got vacume off throttle it was sucking oil straight into the inlet via the pvc, its not a good look out the other end HAHA

andygr32 Rising Star

andygr32

Posted
Posted
Well if ya get stuck for a PVC got a few kickin round, i just took my whole crankcase recirculation setup off, pvc etc, on boost was ok but as soon as i got vacume off throttle it was sucking oil straight into the inlet via the pvc, its not a good look out the other end HAHA

yea, im getting frustrated with the whole oil blowing situation. it does that. vacume = puffs of oil..even without pcv :starwars: so maybe theres sumfin baaaaad goin on...ill let ya know bud :D

NismoGTR33 Apprentice

NismoGTR33

Posted
  • Author
Posted
yea, im getting frustrated with the whole oil blowing situation. it does that. vacume = puffs of oil..even without pcv :P so maybe theres sumfin baaaaad goin on...ill let ya know bud :)

without pvc oil can still blow into the turbo inlet from the cam cover breather pipes, pull the black flexible inlet pipe off see if its wet with oil, unless u have already checked that, in that case its more than likely turbo oil seal or mabey a head problem? valve seals cracked head if its ever been hot or mabey even rings?

NismoGTR33 Apprentice

NismoGTR33

Posted
  • Author
Posted
hey, would you sell a pair of handbrake cables out of one?

Hey, na i dont reckon mate wanna try and keep silver car as complete as i can and sell it still might put the auto and a fresh motor in yet, also the red one im not wrecking just selling as is.

NismoGTR33 Apprentice

NismoGTR33

Posted
  • Author
Posted
yea true to that except. i dont have that pipe already! ha and just had head rebuilt and have excellent compression over all 6cyl.! ha sorry to hijack your thread!!

all good im new here its good to chat to a fellow skyline enthusiast, um yeah i dunno then without really looking at it. where exactly is this oil going ? out the exhaust ?

andygr32 Rising Star

andygr32

Posted
Posted
all good im new here its good to chat to a fellow skyline enthusiast, um yeah i dunno then without really looking at it. where exactly is this oil going ? out the exhaust ?

yea man after decel/vaccume. so not on boost at all! u in launie or hobart

?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...