Jump to content
SAU Community

Recommended Posts

After many many problem with my skyline i finaly found a vacume leak which i was hoping was the cause of my lean idle, lag and super richness on boost. I removed the charcole canister which is brocken and the car seams to run slightly better. Idle is still lean lag is still there but actual driving of the car feels alittle better.

After parkig the car in my drive way after testing how it went I noticed when i pressed the brake pedal the rpm droped. So I pressed it multiply times and the rpm dropped below 500 nearly stalling the car.

Any ideas here? Is this another air leak?

Link to comment
https://www.sau.com.au/forums/topic/335750-vacume-leak-in-r33-gtst/
Share on other sites

sorry to hear that my borrowed intercooler didnt solve your problem dude, i still feel you need a real turbo for response :P

Have you had any change in the behaviour of the braking.. how do ur brakes feel compared to the other silver skyline?? Sorry to say the check valve stops boost entering the brake system so its unlikely to be your problem unless your check valve is broken. Generally if your car goes to stall when you press the brake your brake booster has a leak in the diaphragm.

The brake booster has vacuum pressure on both sides of the diaphragm, when you press the brake pedal in, it lets in atmospheric air pressure into one side of the diaphraghm , the unbalance in the pressures gives you your brake boost. Maybe check your brake lines and get a vacuum tester and check the vacuum at the end of the brake line with the brake pedal both pressed and depressed.. id be keen to check mine as well as its one of the only few places i havent checked for my small air leaks. I think the engine would get a small amount of air from the brake system when the brake is released as the atmospheric air pressure side of the diagraghm gets repressured to vaccum.

Apparently your car can also stall from a few other things in the brake system, like blocked lines, split hoses and a master cylinder leak.. but i dont really see how with my limited knowledge, hopefully an actual mechanic can give us some additional information.. i only learn these things as things on my car break and im looking for answers:P

Jarrod

I have seen this happen on many older cars, pressing the brake pedal repeatedly will either make the engine rev, or stall.

I would check the lines going to the booster and the booster itself as Jarrod mentioned. Listen for a vacuum sound when you depress the brake, that's the booster, you should only hear it while applying pressure. If you still hear vacuum when the brake is depressed and stationary, that could indicate a leak.

Laz

wtf is wrong with 16-19 on idle

For starters, I am using an rb20 ECU, a 0 on any cell on the fuel map is a theoretical Stoich so yeah it may go slightly leaner but not the constant 17-19 i was getting on the way to work today. So i either have a leak, or yeah may be an electrical problem. I might check for voltage drops on the injectors.

Little update on this problem.

I have disconnected my narrow band sensor and fed my Techedge widebands narrowband sim output into the loom. Car is running a lot better mostly sticking at around 14.9arf Still at idle tho its hitting mega lean and slowly moving back to 14.9afr.

I should not have had to replace the sensor as its only a year old. I think it may have been damaged by being too close to the turbo.

Back to the lean idle problem I am thinking there are 2 possible problems.

1. I do in fact still have an air leak. And now that the closed loop is working properly it is able to bring the afrs back to where they should be.

2. My idle needs to be reset.

Will continue to play with it.

afr shouldnt be a constant number at idle i hope you realise . it should swing from rich to lean and back again repeatidly . and i hope its fully warm when your doing this

every time you release the brake pedal you are letting more air into the plenum than the ecu wants in there . hance idle changes

Yes I know when in closed loop the afr should swing rich to lean to rich etc. If you knew exactly how it worked then you would know that anything richer that stoich is seen as rich by the ecu and anything leaner than stoich in seen as lean by the ecu. Meaning the rich to lean to rich swinging should all be very very close to stoich. When monitoring using a wideband you don't actually see the swinging like you would a narrowband guage all you see is a twitch in the numbers/graph.

When having the idle issue my idle is sitting at lean no swinging nothing like that. And yes of course the car has been warmed up first.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...