Jump to content
SAU Community

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

How many people actually got fined for $10,000? Can anyone provide details as to why they got fined $10,000? Is that a fine from the cops or from EPA? Was it on the spot or when you're going through the pit?

http://www.boostcruising.com/forums/index....0225&st=150

But again like everyone said, its not worth the risk with the amount of gain. I just asked the question out of curiousity as I reckon that kinda fine is a bit ridiculous especially when a defect fine is only $100.

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5435627
Share on other sites

So many people de-cat their imports....i just had the standard cat in there, unbloted it, bashed the guts of the car out with a screwdriver and put the cat back in. Made massive flames, like 2m long bright orange flames lol

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5435957
Share on other sites

harden up and run he de-cat- more power, a shitload cheaper and better turbo response

yes apparently its a 10k fine but how can they find out? we dont have EPA in perth

even then is a copper really gonna stick his head under your car? even then hows he gonna see if u've got a gutted cat they dont carry infared thermometers all they can do is 'suspect' u have no cat and then give u a yellow. if u go over the pits with a decat/no cat then u deserve the 10k fine, after u get a yellow u got shitloads of time to take it off.

it was said before, whos actually been done for not having a cat (in perth anyway)

-ive got a 3inch straight through pipe which has had a standard cat chopped in half and welded around it (cat temp sensor still screws into the shell) for sale as my cars written off u wanna buy it PM me (btw this was used for the track only not on the road)

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5436929
Share on other sites

Go run a GRiD backfire with decat in front of a cop car, and get back to us on your "yellow" sticker with a shitload of time before expiry....they can (and have done previously) given as little as 15 minutes on yellow stickers).

You'll get a RED sticker for that shit.

And EPA isn't necessary to get you into shit over here, go give it some juice at night time......we've all seen a de-cat'd car give it some juice at night, and the sudden bright flashes it can cause....that shit can cause short and/or long term damage to vision.

De-cat's are a stupid idea, they do f**k all for performance. 7hp, and what do you get? You can't have a decent conversation in your car, which you have to clean weekly thanks to unburnt fuel being all over the back of it.

Link to comment
https://www.sau.com.au/forums/topic/335959-decat/#findComment-5437256
Share on other sites

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Thanks for that mate always a good help
    • It's not really a calibration issue, if the voltage is really at 2V. If the voltage is 2V, then that's what the TPS is putting out, and the Haltech is seeing that and 2V is about 40% open (you know, between 0.45v being closed and something close to 4.5V being fully open). So, that would suggest that the TPS is maladjusted, on crooked, something something something. Or a wire problem.
    • Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
×
×
  • Create New...