Jump to content
SAU Community

Rb26/ Gtr Turbo Kits

Risking
 Share

Recommended Posts

Risking Grand Master

Risking

Posted
Posted

Both of these are back up for sale due to bullshit time wasters, so If you intend on wasting my time or dont have the funds, piss off and dont bother im not interested!!

sorry for being so blunt but seriously im over time wasters!

Im selling off ONE of these kits only. Which ever does not sell ill be putting back onto my Street driven GTR.

First up is a complete and genuine TRUST TD06-20G twin high mount kit, Has two good condition TD06 turbos with smoothed compressor housings semi polished finish.

A genuine Trust twin manifold which has had some extra bracing welded to the wastegate flange for support

A genuine Trust 60mm wastegate with screamer pipe.

Two dump pipes, both 2.5inch mild steel.

A merge pipe to join the dumps into a generic cat back system.

Intercooler piping from both turbos to the inner wheel arch.

Twin air intakes with 3 inch filters

Oil lines and water line blanks etc

Gaskets and all the hardware to mount it up.

Will spit out +500Kw with ease, not for the faint hearted of wallet shy

Wanting $3800 firm.

Second is a HKS TA45s turbo, which was rebuilt and apparently done 100Km's since rebuilt, it doesnt look like its done anything at all really. Polished compressor housing and a 2.5 inch elbow welded on which is polished as well. Turbo condition is immaculate.

Manifold is a custom job with 1.25 inch runners all 316 stainless. The head flange is 10mm thick as to is the turbo flange. Has bracing and an external gate running off it.

Wastegate is a 50mm HKS item which has been stripped and service with a new diagram. Has a screamer too

Dump pipe is TIG welded 3 inch mild steel with V band to the turbo. will fit a generic cat back

Comes with a braided oil feed line but NO cooler piping or intake etc.

Again a +500Kw kit

Asking $2100

Both kits are in my possession and ready to be sold. I will be keeping which ever doesnt sell I dont mind which one goes.

In sydney will post STRICTLY at buyers expense.

Can offer fitting for locals.

Again please dont waste my time these are serious kits in perfect condition for serious buyers only

Link to comment
https://www.sau.com.au/forums/topic/336532-rb26-gtr-turbo-kits/
Share on other sites
  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...