Jump to content
SAU Community

Recommended Posts

Hey everyone

Im 16 years old now, and just finishing high school, im really interested in learning to be able to service and modify cars, im thinking like performance mods, audio, and just normal servicing etc .. the whole thing, i'd loveee to be able to do up my car myself and so on

I'm not too sure where to get started though, I was thinking of doing a course maybe at tafe or something after high school (was googling them just then, and found this .. http://www.cengage.edu.au/technical-trade-.../auto-mechanics)

But that looks like it'd be a bit too long ..

Does anybody have any suggestions?

Thanks so much, any help would be great

Link to comment
https://www.sau.com.au/forums/topic/336831-automotive-courses/
Share on other sites

I'd say do an automotive apprenticeship first mate, gotta have the basics first ie know how your internal combustion engines, suspension, braking, auto elect systems work before you go modifying them

Cheers Nick

yeahh thats what im after, definitely need to do some kind of course to learn all about it first

just not too sure where to go for that kinda thing? like most of the courses ive seen online take about 2 years ...

how long would an apprenticeship take?

:P thats a bit long ...

I think ill be looking at a traineeship or a tafe course

Btw for anybody interested, tafe runs a 5 week course that looks really good, im definitely gonna do it

http://www.polytechnic.wa.edu.au/short_cou...searchoptions=1

the one on car maintenance .. looks really interesting :)

Are you looking to learn as a way of forging a career? Or just to kickstart a hobby?

If you want to make a living out of it, then an apprenticeship or traineeship is the only way to go. Start your research here

http://www.trainingwa.wa.gov.au/apprentice.../detcms/portal/

If its just a hobby thing, then the tafe course you linked to would be an excellent way to start. Also, star looking into joining an active car club. Offering your services to an enthusiast or events club would be surrounding yourself with like minded individuals, and helping them out (with events stuff, flag marshalling and the like) and you will soon find yourself flooded with more information about cars and stuff than you will know what to do with.

hey guys thanks for all the replies,

nah not looking to make a career out of it, just a hobby

I was thinkin of takin a year off after school to do a traineeship or a tafe course

Rooster what did you mean by an events club etc? sorry just not too sure about these things

Rooster what did you mean by an events club etc? sorry just not too sure about these things

I think he meant clubs like AFARCC (All Fours and Rotary Car Club), WASCC (WA Sporting Car Club) etc, which run alot of motorsport events. You can become a flag marshal, scruitineer etc. Check out CAMS (www.cams.com.au) on how to participate.

  • 7 months later...

hey guys sorry to revive this thread again

just wondering .. is there a skyline manual or something like that?

Most cars have the "gregorys" manual and such ..

Just wanting to learn more about my car and how it works/how to maintain it etc and thought something like that would be nice to have!

Only thing i found is the owners guide from pitstop

tafe is the way to go to get some basic knowledge about how cars actually work

ive been doing a tvet coarse through school and it has really tought me alot

i found it very rewarding and its abit of fun

even though we only pulled apart a corolla motor haha

hey troy,

What course at tafe dya reckon is good?

I was looking at traineeships .. their very specific? I'd like to have more general knowledge etc i think as I just dont have the time to do all the different traineeships to learn about everything!

Hahah, I was thinking of buying some unlicensed car for a few hundred bucks to try and pull apart/fix up etc to have a bit of a learning experience ...

You might as well just work on your own car and do DIYs. If not you can do a light vehicle pre apprentice for basic knowledge of cars and servicing. I suggest you don't go through with an apprenticeship if you just want to do it as a hobby. Would be a waste of 3.5years with such stressful conditions for not much pay. =)

Hey vincent, I would love to work on my own car, but tbh i dont know crap!

all ive done with my car is just basic oil/oil filter changes and air filter ... taken apart the dash/centre panel to spray the panels/change the lights inside to blue .. and that would be about the extent of my knowledge with cars :(

Yeah, id love to do the apprenticeship but I don't have 3.5 years, im currently in uni for 4.5 already in my double degree!

Its a shame cos i have a ton of love for cars but I dont know anything and Im not too sure how to go about learning :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...