Jump to content
SAU Community

Rb26 Complete Motor, T78 33d Kit, Heaps Of Other Bits

boostd gem
 Share

Recommended Posts

boostd gem Enthusiast

boostd gem

Posted
Posted (edited)

hey all, i bought this setup not long ago to put in my 180 but unfortunatly things have changed for me and if i can make most of what it cost me back ill be selling it up.

basic rundown.

RB26DET

sard 600cc injectors

tomei poncams

modded sump for rwd

unknown bottom end. can only be presumed standard.

Heavy duty clutch

loom etc.

$3800

T78 33d kit.

trust mani

hks 50mm gate

dump pipe

turbo looks to be in really good condition other than some slight marks on the comp wheel (run with no filter)

$2900

Power fc

Greddy twin intake

Z32 AFMs

fc commander

$1400

trust oil cooler kit.

sandwich plate etc all lines included with earls fittings

$800

i have other little things like stock ecu, a/c compressor etc.

nothing will be seperated until ive sold the motor/turbo kit.

cost for all of the above complete is $7600 firm.

post-29077-1284532170_thumb.jpg

Edited by boostd gem
GUN_METAL_GTR32 Grand Master

GUN_METAL_GTR32

Posted
Posted

interested in the turbo kit.

what power did u make with this setup at what rpm. do u have a dyno graph?

what is a t78 rated at horsepower wise?

thanks

julz

nisskid Grand Master

nisskid

Posted
Posted

for anyone interested, this wasnt run without a air filter, so no worries there, it's just one of the air filter's was damaged so i didnt worry giving it to him. they were run with blitz twin pods so there is no issue there. I'm also pretty sure this engine runs oil restricters due to the oil pressure readings it was getting (always really good).

this engine is built for huge power, if that's what u want, then u cant go past this package.

nisskid Grand Master

nisskid

Posted
Posted
Is this your old engine nisskid?

yeh mate, really strong engine, and the T78 was amazing, i didnt wanna get rid of it, but had to let it go as i was in too much debt because of it haha

i just wanna see someone get this and give it a proper tune, see what it can do, i lost the tune not long after i bought the car and was too retarded to work the boost controller, so it ran on a base map and 12psi for most of the time i had it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...